Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class)
Inch TEK self-drilling screws, Special TEKS/2 point class as printed by the source for heavier gauge metals: No. 12 and 1/4" sizes drilling .210"–.375", carrying the longest tabulated drill points (.437"/.468"). The long-point variant that covers the band above TEKS/4.
Last updated: 2026-11
Specifications
The collected selection table prints this class under its own label — "Heavier Gauge Metals Special Teks / 2" — and gives it the two largest sizes with the deepest drilling windows in the collected ladder: No. 12 at .210–.345" and 1/4" at .250–.375". The drill points are the longest tabulated anywhere in the series, .437" at No. 12 and .468" at 1/4", because the flute must cut a stack three to four times thicker than the TEKS/2 light-gauge window before the threads engage. The label is reproduced as printed: the source carries it as a special long-point variant of the /2 class, not as a TEKS/5, and no TEKS/5 per-diameter table appears in the collected source. The class starts where TEKS/4 ends — .210" at No. 12, .250" at 1/4" — so the two pages split the heavier-gauge band cleanly between them. The collected table carries no head-form, thread-pitch or length columns; those are fixed at quotation with the panel system.
| Point class | Special TEKS/2 — heavier gauge metals point class, label as printed by the collected selection table |
|---|---|
| Screw sizes (tabulated) | No. 12, 1/4" |
| Material thickness range per size | No. 12 .210–.345" · 1/4" .250–.375" |
| Drill-point length per size | No. 12 .437" · 1/4" .468" (inches + decimal as printed) |
| Drilling window (class) | .210" to .375" total metal thickness, size-dependent — see the per-size ladder |
| Materials | Case-hardened carbon steel with corrosion-resistant plating is the standard construction for inch TEK self-drillers; stainless (410) and other finishes confirmed at quotation |
| Screw diameter | Recommended material thickness (inches) | Drill-point length — inches | Drill-point length — decimal |
|---|---|---|---|
| No. 12 | .210 To .345 | 7/16 | .437 |
| 1/4" | .250 To .375 | 15/32 | .468 |
Materials
- Case-hardened carbon steel with corrosion-resistant plating is the standard construction for inch TEK self-drillers; stainless (410) and other finishes confirmed at quotation
Ordering & documentation
Documents
Shipments of Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for special teks/2 self-drilling screws (heavier gauge long-point class) is 10,000 pieces (applies to the standard sizes and finishes for special teks/2 self-drilling screws (heavier gauge long-point class); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for special teks/2 self-drilling screws (heavier gauge long-point class) run 3–7 days. Quantities or variants of special teks/2 self-drilling screws (heavier gauge long-point class) outside the standard range are confirmed at quotation.
Storage & shipping
Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store special teks/2 self-drilling screws (heavier gauge long-point class) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why choose the Special TEKS/2 over the other TEK point numbers?
By total steel thickness. The collected selection table assigns the deepest windows in the collected ladder: No. 12 drills .210–.345" and 1/4" drills .250–.375", on the longest tabulated drill points: the point must pierce the whole stack in one operation, so a point class below the total thickness stalls or snaps its tip, and a class far above it leaves an unnecessarily long drill flute that wastes engagement. Match the printed material-thickness range for your screw diameter to the measured stack, and step up to the next TEK number when the stack exceeds it. State the total thickness on the RFQ so the point class is confirmed against the ladder rather than assumed.
Is this a TEK 5 point?
Not by the collected evidence. The source prints this class as "Special Teks / 2" — a long-point special of the /2 class — and publishes no TEKS/5 per-diameter table, so this page uses the printed designation and the printed windows, nothing more. Industry prose elsewhere names a TEK 5 class for structural steel, but until a source prints its per-diameter ladder it is not stated on this page; if your stack exceeds .375" at 1/4", confirm the point class explicitly at quotation.
What is the MOQ and lead time for these self-drilling screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for inch TEK screws state?
State the screw gauge (No. 6, No. 8, No. 10, No. 12, 1/4"), the TEK point number required for the total metal thickness being drilled, head form and drive, length, finish (for example zinc plated or 410 stainless), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your Special TEKS/2 Self-Drilling Screws (Heavier Gauge Long-Point Class)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support