Metric Thread Stress and Shear Areas

Per metric thread size M 5 to M 100: the bolt's tensile stress area, and the bolt and nut thread strip (shear) areas per one diameter of engagement under the 6H/6g and 6H/4g6g fits — the areas behind thread-strength and thread-stripping checks.

Last updated: 2026-11

Request a Quote

Metric Thread Stress and Shear Areas in an industrial setting
Illustrative image redrawn from real Metric Thread Stress and Shear Areas product references — not a photograph of stocked items.

Specifications

Two failure modes live in a threaded connection, and each is checked against its own area. Tension fails the bolt across its tensile stress area — the effective section blending pitch and minor diameter (M 10 x 1.5: 57.990). Shear strips the threads, and that check runs over the thread strip area: the load-bearing helical flank area generated per one diameter of thread engagement, tabulated here separately for the bolt and the nut, and separately for the 6H/6g and 6H/4g6g fit combinations — the nut side carries the larger area (M 16 x 2: bolt 417.55 / 429.92, nut 569.12). The ladder runs M 5 x 0.8 through M 100 x 6. Read it as a set: tensile stress area for the bolt-strength check, strip areas for the engagement check — a common design step is dividing the bolt's tensile load by the strip area to get the bearing pressure on the flanks and sizing engagement length so that the threads, not the bolt, are not the weak link (stripping is sudden; bolt fracture gives warning). Note the source's own quirks, carried verbatim and flagged: the M 8 row's tensile cell prints "5 36.609" with a stray leading 5, and its designation column prints "M12 x 1" against the M 12 coarse pitch of 1.75. Thread tolerances and shear strengths are per RFQ against the governing standards.

Size range M 5 x 0.8 to M 100 x 6, 21 thread sizes as the source designates them
Tensile stress area Per size, e.g. M 6 x 1: 20.123; M 20 x 2.5: 244.79; M 48 x 5: 1,473.2; M 100 x 6: 6,994.7
Bolt thread strip area (L e = 1 diameter) Under 6H/6g and under 6H/4g6g, e.g. M 12: 227.72 / 234.86; em-dash cells at M 22 and M 27 in the 6H/4g6g column as printed
Nut thread strip area (L e = 1 diameter) Under the "6H6g and H/4g6g" header as printed, e.g. M 12: 313.41; M 36 x 4: 3,026.2
Reading Areas in mm 2 (per the values' magnitude and use); engagement basis is one nominal diameter L e
Not tabulated Shear strengths, thread tolerance classes, required engagement lengths, torque values — per RFQ
Metric thread stress and shear areas (M 5 - M 100)As printed on the collected page: tensile stress area per thread, and bolt/nut thread strip areas per one diameter of engagement (Le = 1 Diameter) under the tabulated fit combinations. Two-row header carried verbatim (the group headers span two columns). Em-dash cells mark values the source does not tabulate. Verification: re-fetched from the live page 2026-11-01, all 23 rows token-for-token equal to the x127 corpus.
ThreadTensile Stress AreaBolt Thread Strip Area, Le = 1 DiameterNut Thread Strip Area, Le = 1 Diameter
6H/6g6H/4g6g6H6g and H/4g6g
M5 x 0.814.18335.36637.08549.994
M6 x 120.12351.87554.17473.145
M8 x 1.25 36.60997.290100.74134.63
M10 x 1.557.990155.80160.73214.77
M12 x 184.267227.72234.86313.41
M14 x 2115.44313.94323.24434.47
M16 x 2156.67417.55429.92569.12
M20 x 2.5244.79665.58682.06907.76
M22 x 2.5303.40814.67—1,100.3
M24 x 3352.50971.10994.231,320.2
M27 x 3459.411,246.7—1,674.3
M30 x 3.5560.591,549.21,582.52,086.5
M36 x 4816.722,271.52,315.83,026.2
M42 x 4.51,120.93,120.23,175.24,168.3
M48 x 51,473.24,119.54,187.35,482.0
M56 x 5.52,030.05,680.35,769.47,510.2
M64 x 62,676.07,483.67,596.49,847.3
M72 x 63,459.89,574.29,718.512,478
M80 x 64,344.111,92212,10115,419
M90 x 65,590.815,21715,44619,534
M100 x 66,994.718,85619,17024,059
  • Row 4 (M8 x 1.2): M8 tensile cell prints "5 36.609" with a stray leading "5" — verified present on the live page itself 2026-11-01; carried verbatim, not normalized (the plausible M 8 coarse-series tensile stress area is 36.609)
  • Row 6 (M12 x 1): designation prints "M12 x 1" (ISO metric coarse pitch at M 12 is 1.75) — the source's own designation column, carried verbatim
  • Row 4 (M8 x 1.2): designation prints "M8 x 1.2" (ISO coarse pitch at M 8 is 1.25) — carried verbatim
  • Row 1 (): nut-column header prints "6H6g and H/4g6g" (vs the bolt columns' "6H/6g", "6H/4g6g" forms) — the source's own header labels, carried verbatim
  • Row 10 (M22 x 2.5): em-dash cells at M 22 and M 27 in the 6H/4g6g bolt column: values not tabulated by the source for that combination — carried verbatim

Materials

  • Stress and strip areas are thread geometry — they pair with the material strengths of the bolt grade and nut class to decide whether the thread or the bolt fails first. When you RFQ threaded fasteners, give size, pitch, grade/class and engagement available in the joint; where engagement is short we flag the stripping check explicitly and quote against the geometry on this table

Ordering & documentation

Documents

Shipments of Metric Thread Stress and Shear Areas are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Metric Thread Stress and Shear Areas orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Metric Thread Stress and Shear Areas), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for metric thread stress and shear areas is 10,000 pieces (applies to the standard sizes and finishes for metric thread stress and shear areas; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for metric thread stress and shear areas run 3–7 days. Quantities or variants of metric thread stress and shear areas outside the standard range are confirmed at quotation.

Storage & shipping

Metric Thread Stress and Shear Areas are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store metric thread stress and shear areas dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When do I use the tensile stress area versus the thread strip areas on this table?

Different failure, different area. The tensile stress area answers "will the bolt break in tension?" — divide the tensile load by it to get the stress you compare against the grade's strength (this is the same area the clamp-load and torque calculations use). The thread strip areas answer "will the threads shear off?" — they give the helical flank area engaged per one diameter of engagement, so the check is: bolt or nut load, divided by strip area, compared against the shear strength of the weaker member (usually the nut, if materials are mismatched). Note the nut strip area is consistently the largest column — the internal thread carries more flank area per diameter of engagement. If the engagement your joint allows is shorter or longer than one diameter, scale the strip area linearly with engagement; the check then tells you the minimum engagement before the threads strip before the bolt yields.

What is the difference between the 6H/6g and 6H/4g6g columns, and why do two cells print an em dash?

They are two fit combinations between the nut (6H tolerance position) and the bolt plating/thread tolerance: 6g is the standard external thread fit, while 4g6g is a tighter external tolerance used where plating allowance or fit consistency matters — the tighter external fit leaves slightly more usable thread overlap, which is why the 6H/4g6g strip areas print a few percent larger (M 24 x 3: 971.10 vs 994.23). The table carries the combination the source tabulates on the nut side under a single merged header ("6H6g and H/4g6g"), carried verbatim. The em-dash cells at M 22 x 2.5 and M 27 x 3 mark values the source does not tabulate for the 6H/4g6g combination — read those rows from the 6H/6g column and treat the gap as a source gap, not a zero: for those two sizes, confirm the fit basis on the RFQ.

What is the MOQ and lead time for Metric Thread Stress and Shear Areas?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for Metric Thread Stress and Shear Areas state?

State the full designation (Metric Thread Stress and Shear Areas), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Metric Thread Stress and Shear Areas inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your Metric Thread Stress and Shear Areas
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.