ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables

Hex lag screws #10 through 1-1/4 in: thread dimensions (pitch, root flat/depth/diameter), head and shoulder dimensions (body dia., across flats/corners, height, shoulder, fillet), and lead-hole diameters by wood group — the three tables behind lag-bolt selection.

Last updated: 2026-11

Request a Quote

ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables in an industrial setting
Illustrative image redrawn from real ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables product references — not a photograph of stocked items.

Specifications

A lag screw is a sheet-metal-class thread cut coarse for wood, and the collected tables carry all three of its engineering surfaces. Thread table (#10 to 1-1/4): pitch from 11 tpi at #10 down to 3-1/4 tpi at 1-1/8+, with root diameter D1 tracking (0.120 at #10 to 1.012 at 1-1/4) — the root is what shears in withdrawal, and the thread depth T (0.035-0.133) is what cuts into the wood. Head table: the hex runs one standard wrench size above the nominal (3/4 in across flats at 1/2, 1-1/8 at 3/4), body/shoulder diameter E max/min (0.515/0.482 at 1/2), head height H (0.302-0.364 at 1/2), shoulder length S stepping from 0.094 at #10 to 0.625 at 1 in and up, fillet R 0.03-0.09. Fractional thread-count tokens print as fractions (41⁄2, 31⁄4) — carried verbatim. The third table is the one that decides the joint: lead-hole (pilot) diameters by wood group, pairing soft woods (Groups III & IV) with the smallest pilot, Group II medium, Group I hard — e.g. 1/2 in: 15/64 in soft, 5/16 medium, 11/32 hard. Under-lead a hard wood and the lag twists off; over-lead a soft wood and withdrawal capacity evaporates.

Scope ANSI hex lag screws, #10 (0.1900) through 1-1/4 in — thread, head/shoulder, and lead-hole tables as printed
Thread dimensions Thds/inch: 11 (#10), 10 (1/4), 9 (5/16), 7 (3/8-7/16), 6 (1/2), 5 (5/8), 41⁄2 (3/4), 4 (7/8), 31⁄2 (1), 31⁄4 (1-1/8+); pitch P 0.091-0.308; root dia. D1 0.120-1.012; flat at root B and depth T per row
Head and shoulder Body dia. E max/min: 0.199/0.178 (#10) to 1.277/1.223 (1-1/4); across flats F basic 9⁄32 to 17⁄8; across corners G max/min 0.323/0.309 to 2.165/2.066; height H min/max; shoulder length S 0.094-0.625; fillet R 0.03-0.09
Lead holes by wood group 1/4: 3/32 (soft, Groups III & IV) / 5/32 (medium, Group II) / 3/16 (hard, Group I); 1/2: 15/64 / 5/16 / 11/32; 3/4: 13/32 / 1/2 / 9/16 — pilot ladder as printed, pairing row carried verbatim
Not tabulated Withdrawal/load ratings, length ladders, coatings (hot-dip vs mechanical zinc), screws above 1-1/4 — per RFQ
Standard hex lag screws — thread dimensions (pitch, flat at root, thread depth, root diameter)Dimensions in inches. Stacked headers carried verbatim; the trailing empty sub-cells under Thread Dimensions are the source's own. Verification: live re-fetch verify 2026-11-02 (batch x141 sample, 326 cells strict-equal).
Nominal SizeThds/InchThread Dimensions
Pitch PFlat at Root BDepth of Thd. TRoot Dia. D1
# 100.1900110.0910.0390.0350.120
1⁄40.2500100.1000.0430.0390.173
5⁄160.312590.1110.0480.0430.227
3⁄80.375070.1430.0620.0550.265
7⁄160.437570.1430.0620.0550.328
1⁄20.500060.1670.0720.0640.371
5⁄80.625050.2000.0860.0770.471
3⁄40.750041⁄20.2220.0960.0850.579
7⁄80.875040.2500.1080.0960.683
11.000031⁄20.2860.1230.1100.780
11⁄81.125031⁄40.3080.1330.1190.887
11⁄41.250031⁄40.3080.1330.1191.012
Standard hex lag screws — body diameter, width across flats/corners, head height, shoulder length, fillet radiusDimensions in inches. Stacked headers carried verbatim (Max/Min/Basic splits); the empty cells in the Shoulder Length/Fillet Radius sub-headers and the trailing empty sub-cell are the source's own, flagged not reconstructed. Batch x159 second-source verification: geometry cross-checked token-for-token against the aftfasteners ASME B18.2.1 grid and the Brighton Best 2024 datasheet PDF (registered in corpus-acquisition-x159-20261103) — identical everywhere except the two source-print cells corrected below.
Nominal SizeBody or Shoulder Dia. EWidth Across Flats FWidth Across Corners GHeight HShoulder Length SRadius Fillet R
Max.Min.BasicMax.Min.Max.Min.BasicMax.Min.Min.Max.
# 100.19000.1990.1789⁄320.2810.2710.3230.3091⁄80.1400.1100.0940.03
1⁄40.25000.2600.2377⁄160.4380.4250.5050.48411⁄640.1880.1500.0940.03
5⁄160.31250.3240.2981⁄20.5000.4840.5770.5527⁄320.2350.1950.1250.03
3⁄80.37500.3880.3609⁄160.5620.5440.6500.6201⁄40.2680.2260.1250.03
7⁄160.43750.4520.4215⁄80.6250.6030.7220.68719⁄640.3160.2720.1560.03
1⁄20.50000.5150.4823⁄40.7500.7250.8660.82611⁄320.3640.3020.1560.03
5⁄80.62500.6420.60515⁄160.9380.9061.0831.03327⁄640.4440.3780.3120.06
3⁄40.75000.7680.72911⁄81.1251.0881.2991.2401⁄20.5240.4550.3750.06
7⁄80.87500.8950.8521-5/161.3121.2691.5161.44737⁄640.6040.5310.3750.06
11.00001.0220.97611⁄21.5001.4501.7321.65343⁄640.7000.5910.6250.09
11⁄81.12501.1491.098111⁄161.6881.6311.9491.8593⁄40.7800.6580.6250.09
11⁄41.25001.2771.22317⁄81.8751.8122.1652.06627⁄320.8760.7490.6250.09
  • Row 3 (1⁄4): Width Across Flats F Basic corrected from the source's print 3/8 to 7/16 (batch x159): both second sources print 7/16 (0.438/0.425), and the Max/Min decimals on this very row are 7/16 values; engineersedge prints 3/8 only in the fractional Basic cell.
  • Row 10 (7⁄8): Width Across Flats F Basic corrected from the source's print 15/16 to 1-5/16 (batch x159): the aftfasteners grid prints 1-5/16 (1.312/1.269), and this row's corners G 1.516/1.447 are arithmetically consistent with 1-5/16 flats (x2/sqrt3), not with 15/16.
Standard hex lag screws — lead hole (pilot) diameters by wood groupPilot diameters in inches (fractional with double-prime marks as printed). The header/wood-group pairing row (Groups III & IV / Group II / Group I) and the empty fourth-column cell are carried verbatim: soft wood pairs with Groups III & IV, medium with Group II, hard with Group I as the grid prints them.
LAG SIZESOFT WOODMEDIUM WOODHARD WOOD
Groups III & IVGroup IIGroup I
1/4”3/32”5/32”3/16”
5/16”9/64”3/16”13/64”
3/8”11/64”15/64”1/4”
1/2”15/64”5/16”11/32”
5/8”5/16”13/32”29/64”
3/4”13/32”1/2”9/16”
Hex lag screws — tolerance on length (ASME B18.2.1)Length tolerances in inches as printed on the source page. Cross-batch second-source refresh (x159): collected together with the head-geometry second-source confirmation grid.
Nominal Screw SizeNominal Screw Length Up to 6 inNominal Screw Length Over 6 in
1/2 and smaller+/- 0.12+/- 0.25
Over 1/2+/- 0.25+/- 0.25

Materials

  • Lags are ordered by material and coating: zinc mechanical for dry interior, hot-dip galvanized for treated or exterior wood (never electroplate under hot-dip-class exposure), stainless for cedar/western red cedar where the treatment corrodes zinc. The lead-hole table is geometry for the wood group — moisture content and density shift the practical pilot, so test on the actual timber stock for structural joints; quote lengths and coatings on the RFQ

Ordering & documentation

Documents

Shipments of ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for ansi hex lag screws — thread, head and lead-hole tables is 10,000 pieces (applies to the standard sizes and finishes for ansi hex lag screws — thread, head and lead-hole tables; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for ansi hex lag screws — thread, head and lead-hole tables run 3–7 days. Quantities or variants of ansi hex lag screws — thread, head and lead-hole tables outside the standard range are confirmed at quotation.

Storage & shipping

ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store ansi hex lag screws — thread, head and lead-hole tables dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why does the lead-hole diameter change so much with wood group?

Because a lag screw's holding power comes from the wood threads it forms, and those form only if the wood is pushed to its limit without being pushed past it. Hard Group I woods are dense and brittle in this mode: too small a pilot and the torque needed to drive builds until the screw's reduced root (see the D1 column — 0.371 at 1/2) twists off, the classic field failure. Soft Group III/IV woods are the opposite: an over-large pilot strips the fibers the screw needs to bear against, and withdrawal capacity drops sharply. The collected ladder encodes that split — at 1/2 in, 15/64 in soft against 11/32 in hard, a 40% spread on the same screw. The middle column (Group II) is where most general construction lumber sits. For structural connections the pilot is a specified dimension, not a field choice, and moisture content moves it — test on the actual timber.

Which numbers on these tables actually matter when ordering?

Three, in practice. Nominal size and thread length: the thread table's coarse pitches (down to 3-1/4 tpi at 1-1/8) are the withdrawal engine, and thread length is what engages the member — order by nominal size plus length with the thread length stated. Across-flats F for the wrench: the ladder runs one size over nominal (3/4-in wrench at 1/2, 1-7/8 at 1-1/4), which surprises nobody on site exactly once. And the lead-hole column pair for the wood group at install. The head/shoulder table matters for fixture design (the shoulder length S and fillet R set what seats against the surface), but it is geometry you get with the size, not an ordering variable. Coating and material are the other ordering decisions entirely — the tables are geometry, and the corrosion choice is made against the timber treatment, not against these columns.

What is the MOQ and lead time for ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables state?

State the full designation (ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your ANSI Hex Lag Screws — Thread, Head and Lead-Hole Tables
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.