ISO 7380-1 Hexagon Socket Button Head Screws
ISO 7380-1 hexagon socket button head screws M3 to M16 — the flangeless low-domed socket screw — with the full collected per-size table: thread pitch, head and shank tolerances, socket sizing, minimum tensile loads per property class (8.8/10.9/12.9 and 70/80 as printed) and thread length b, a strength-tabulated counterpart to the socket cap screw line.
Last updated: 2026-11
Specifications
The ISO 7380-1 button head is what a socket cap screw becomes when the head must disappear sideways rather than downward: a low, wide dome with a hexagon socket, trading head height and bearing diameter against tensile capacity relative to the cap-screw line. The tabulated data is unusually complete for a screw of this type — it tabulates not just geometry (thread pitch P, head diameter d k max/min, shank d s max/min, head height k, socket depth t, across-flats s nominal with tolerances and across-corners e min) but a minimum tensile load row per diameter for five property-class printings: 8.8, 10.9 and 12.9 carrying a superscript ②, and 70 and 80 carrying a superscript ③. No legend is published for those markers, so this page reproduces them verbatim rather than interpreting — read the row that matches the class your drawing calls out. The numbers tell the engineering story directly: at M6 the 8.8 row carries 12,900 N against 19,600 N at 12.9, and the stainless-class rows carry proportionally less. The series runs M3 to M16, with thread length b growing from 18 to 44 mm. A second collected catalog source corroborates the head-diameter row 8/8 across the series and adds one column the specification table does not print — the flange/bearing diameter dc max, 6.9 mm at M3 up to 34 mm at M16 — tabulated below with that source's decimal commas preserved. The same second source also tabulates minimum tensile loads for the steel classes — 23 of its 24 load cells match this page's primary rows exactly, and the one difference (8560 N against 8506 N at M4, class 12.9) is left as printed by each source and flagged on the corroboration table below. One designation note: "-1" is the flangeless version — where a flange or collar under the head is part of the callout, that is the -2 designation, and the security variant with a pin-in-socket drive is covered by the ISO 7380-2 page on this site.
| Standard | ISO 7380-1 — hexagon socket button head screws ("-1" is without a flange/collar; the flanged version is the -2 designation) |
|---|---|
| Series | M3, M4, M5, M6, M8, M10, M12, M16 |
| Tabulated geometry | Per size: pitch P, head dia d k max/min, shank dia d s max/min, head height k max/min, socket depth t min, across-corners e min, socket across-flats s nominal/max/min |
| Minimum tensile load | Tabulated per size per printed class row — 8.8 ② / 10.9 ② / 12.9 ② / 70 ③ / 80 ③ (3220–154,000 N across the series); the ②/③ markers are reproduced as printed, no legend is published |
| Thread length b | 18 mm (M3) to 44 mm (M16) as tabulated |
| Family notes | Flanged counterpart = ISO 7380-2 designation family (security pin-in-socket variant page on this site); socket cap screw counterpart = DIN 912 / ISO 4762 |
| Nominal thread | P — pitch (mm) | d k max (mm) | d k min (mm) | d s max (= nominal) (mm) | d s min (mm) | k max (mm) | k min (mm) | t min (mm) | e min (mm) | s nominal (mm) | s max (mm) | s min (mm) | Min tensile load 8.8 ② (N) | Min tensile load 10.9 ② (N) | Min tensile load 12.9 ② (N) | Min tensile load 70 ③ (N) | Min tensile load 80 ③ (N) | b — length of thread (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.7 | 5.4 | 3 | 2.86 | 1.65 | 1.4 | 1.04 | 2.303 | 2 | 2.08 | 2.02 | 3220 | 4180 | 4910 | 2810 | 3220 | 18 |
| M4 | 0.7 | 7.6 | 7.24 | 4 | 3.82 | 2.2 | 1.95 | 1.3 | 2.873 | 2.5 | 2.58 | 2.52 | 5620 | 7300 | 8560 | 4910 | 5620 | 20 |
| M5 | 0.8 | 9.5 | 9.14 | 5 | 4.82 | 2.75 | 2.5 | 1.56 | 3.443 | 3 | 3.08 | 3.02 | 9080 | 11800 | 13800 | 7950 | 9080 | 22 |
| M6 | 1 | 10.5 | 10.07 | 6 | 5.82 | 3.3 | 3 | 2.08 | 4.583 | 4 | 4.095 | 4.02 | 12900 | 16700 | 19600 | 11200 | 12900 | 24 |
| M8 | 1.25 | 14 | 13.57 | 8 | 7.78 | 4.4 | 4.1 | 2.6 | 5.723 | 5 | 5.14 | 5.02 | 23400 | 30500 | 35700 | 20400 | 23400 | 28 |
| M10 | 1.5 | 17.5 | 17.07 | 10 | 9.78 | 5.5 | 5.2 | 3.12 | 6.863 | 6 | 6.14 | 6.02 | 37100 | 48200 | 56600 | 32400 | 37100 | 32 |
| M12 | 1.75 | 21 | 20.48 | 12 | 11.73 | 6.6 | 6.24 | 4.16 | 9.149 | 8 | 8.175 | 8.025 | 53900 | 70200 | 82400 | 47200 | 53900 | 36 |
| M16 | 2 | 28 | 27.48 | 16 | 15.73 | 8.8 | 8.44 | 5.2 | 11.429 | 10 | 10.175 | 10.025 | 100000 | 130000 | 154000 | 87900 | 100000 | 44 |
| Thread | dk max (mm) | dc max (mm) |
|---|---|---|
| M3 | 5,7 | 6,9 |
| M4 | 7,6 | 9,4 |
| M5 | 9,5 | 11,8 |
| M6 | 10,5 | 13,6 |
| M8 | 14 | 17,8 |
| M10 | 17,5 | 21,9 |
| M12 | 21 | 26 |
| M16 | 28 | 34 |
- Decimal commas are the second source's own print convention, preserved verbatim (e.g. 5,7 = 5.7 mm); no values converted, merged or derived.
- Second-source corroboration: this source's dk max row matches the primary table's d k max column 8/8 across M3-M16; the dc max flange/bearing row is additional information the primary specification table does not print.
- The second source labels the row "ISO 7380-1/-2"; on the flangeless -1 screw dc is the bearing-circle maximum, on the flanged -2 it is the flange diameter maximum. The source does not split the row by part — read dc as the printed maximum for the size, per the source's own convention.
- The same source page also prints ISO 10642 and DIN 34805 rows; neither is part of this table (10642 adjudicates onto the registered countersunk cap-screw page; the 34805 rows are interleaved/uncertain in the intake and are deliberately not transcribed).
| Thread | 8.8 (N) | 10.9 (N) | 12.9 (N) |
|---|---|---|---|
| M3 | 3220 | 4180 | 4910 |
| M4 | 5620 | 7300 | 8506 |
| M5 | 9080 | 11800 | 13800 |
| M6 | 12900 | 16700 | 19600 |
| M8 | 23400 | 30500 | 35700 |
| M10 | 37100 | 48200 | 56600 |
| M12 | 53900 | 70200 | 82400 |
| M16 | 100000 | 130000 | 154000 |
- Second-source corroboration: 23 of 24 load cells match the primary table exactly across M3-M16 and classes 8.8/10.9/12.9 (e.g. 3220/4910 N at M3, 100000/154000 N at M16).
- Source conflict, not adjudicated: at M4 class 12.9 the primary source prints 8560 N and this second source prints 8506 N — a digit-transposition shaped difference. Both values stay as printed by their own sources; confirm against the manufacturer certificate when the callout is class 12.9 at M4.
- The second source prints no 70/80 stainless-class tensile rows and no per-size thread length b — those columns remain primary-table-only on this page.
- The same source page also carries DIN 34805-1/-2 and ISO 7380 geometry tables; the 34805 tables were transcribed onto their own page in batch x212, and the ISO 7380 geometry columns are not re-tabulated here (the primary table already carries them).
Materials
- Steel, property classes 8.8 / 10.9 / 12.9 (per the collected tensile-load rows)
- Stainless-class rows 70 / 80 (per the collected tensile-load rows, markers as printed)
Ordering & documentation
Documents
Shipments of ISO 7380-1 Hexagon Socket Button Head Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 7380-1 Hexagon Socket Button Head Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 7380-1 Hexagon Socket Button Head Screws), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for iso 7380-1 hexagon socket button head screws is 10,000 pieces (applies to the standard sizes and finishes for iso 7380-1 hexagon socket button head screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 7380-1 hexagon socket button head screws run 3–7 days. Quantities or variants of iso 7380-1 hexagon socket button head screws outside the standard range are confirmed at quotation.
Storage & shipping
ISO 7380-1 Hexagon Socket Button Head Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 7380-1 hexagon socket button head screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Button head or socket cap screw — what does the choice cost?
Height versus strength. The button head is the lower-profile head — that is why it wins inside slides, clamped covers and flush-clearance envelopes — but the wider, thinner head carries a lower tensile load than the cap-screw head, and the collected table quantifies it per class and size — at M8, for example, the strongest printed row is 35,700 N at 12.9. If the joint was sized for a cap screw, do not substitute a button head without re-checking that row.
What should an RFQ for ISO 7380-1 screws state?
The designation (ISO 7380-1 for the flangeless head), thread size M3–M16 and length, property class — 8.8/10.9/12.9 steel or the 70/80 stainless rows — finish, any certificate requirement such as a mill test report per EN 10204 3.1, and quantity per size. Minimum tensile loads per row are in the table on this page; per-length availability and commercial terms follow the quotation.
What is the MOQ and lead time for these screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Common sizes in this designation are widely stocked — confirm the exact schedule against quantity and size mix at quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 7380-1 Hexagon Socket Button Head Screws inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your ISO 7380-1 Hexagon Socket Button Head Screws
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support