TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws
Countersunk self-tapping security screws on the 6-lobe pin TX drive, No.2–No.14 as tabulated: head diameters 4.3–12.4 mm, head heights 1.3–3.8 mm, tool sizes TX6–TX30. A2/A4 stainless steel; flush-seating thread-cutting fixing, two-way reusable.
Last updated: 2026-11
Specifications
This is the flush-seating counterpart of the TX04: a countersunk self-tapping screw that cuts its own thread and then disappears into the countersink — the low-profile choice for sheet metal, plastics and any panel where a proud head would catch or invite prying. The collected tabulation runs No.2 to No.14, with head diameters from 4.3 mm to 12.4 mm, head heights from 1.3 mm to 3.8 mm, and driver sizes TX6 to TX30, shared across adjacent gauges as on the rest of the line. The drive is the standard pin-TX arrangement: six lobes around a centre pin, medium security against vandals and thieves at low cost, reusable two-way so maintenance stays possible. Length availability is legible in the collected matrix only for two gauges — No.2 marked available to order in 3/16"–1" (4.5–25 mm) and No.7 in 1/4"–2 3/4" (6.5–70 mm) — with the remaining columns unmarked and therefore confirmed at quotation. Materials per the collected page are A2 and A4 stainless steel.
| Designation | TX05 — countersunk self-tapping security screw, 6-lobe pin TX drive; thread-cutting, seats flush in a countersunk hole |
|---|---|
| Gauge range (tabulated) | No.2, No.4, No.6, No.7, No.8, No.10, No.12, No.14 |
| Head diameter dk per gauge (mm) | No.2 4.3 · No.4 4.9 · No.6 6.6 · No.7 7.85 · No.8 8.4 · No.10 9.3 · No.12 10.6 · No.14 12.4 |
| Head height k per gauge (mm) | No.2 1.3 · No.4 1.5 · No.6 2.1 · No.7 2.45 · No.8 2.6 · No.10 3.0 · No.12 3.4 · No.14 3.8 |
| Tool size per gauge | No.2 TX6 · No.4 TX10 · No.6 TX15 · No.7 TX15 · No.8 TX20 · No.10 TX25 · No.12 TX27 · No.14 TX30 |
| Length availability (as marked) | No.2 marked available to order in 3/16"–1" (4.5–25 mm); No.7 marked available to order in 1/4"–2 3/4" (6.5–70 mm); other gauges carry no legible marking |
| Security principle | Two-way reusable pin-TX drive — medium security; removal and reinstallation only with the matching pin-TX driver |
| Materials (collected) | A2 and A4 stainless steel |
Materials
- A2 stainless steel
- A4 stainless steel
Ordering & documentation
Documents
Shipments of TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for tx05 6-lobe pin tx countersunk self tapping security screws is 10,000 pieces (applies to the standard sizes and finishes for tx05 6-lobe pin tx countersunk self tapping security screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for tx05 6-lobe pin tx countersunk self tapping security screws run 3–7 days. Quantities or variants of tx05 6-lobe pin tx countersunk self tapping security screws outside the standard range are confirmed at quotation.
Storage & shipping
TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store tx05 6-lobe pin tx countersunk self tapping security screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
TX04 or TX05 for a sheet-metal panel?
The drive and the thread-cutting behaviour are the same line; the decision is the head. TX05 seats flush in a countersunk hole — right for sliding parts, handles and anything a passing hand or tool could catch on — while TX04 (supplied as a pan head per the collected legend) keeps a low but proud dome that tolerates thinner sheet without countersinking. Note the tabulated heads differ in envelope at the same gauge: No.8 reads 8.4 mm by 2.6 mm on TX05 versus 7.6 mm by 2.2 mm on TX04, so hole preparation should follow the page you actually buy from.
Does self-tapping mean I can skip the pilot hole?
No — self-tapping cuts its own internal thread, but it still needs the right pilot hole diameter for the gauge and substrate, or the screw will bind or strip. The collected table tabulates nominal sheet diameters per gauge (for example No.8 at 4.2 mm) which size that pilot calculation, not a hole to skip. In plastics and thin sheet the pilot matters even more; confirm against the substrate at quotation.
What is the MOQ and lead time for these security screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; sizes quoted as available to order, and non-standard sizes or materials, are quoted with a confirmed schedule. Confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for these security screws state?
State the designation code (TX01 through TX20) and head style, the drive (6-lobe pin TX — the matching pin-TX driver or bit is required), nominal thread size and length, material and finish, the substrate or mating nut where relevant, required certificates, and quantity per size — plus destination country.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your TX05 6-Lobe Pin TX Countersunk Self Tapping Security Screws
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support