Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy)

Dimensions and mechanical properties for ASME B18.3 low head socket cap screws in the six sizes #8 through 1/2 — the reduced-head variant for clearance-limited assemblies — transcribed row-for-row from the collected chart.

Last updated: 2026-11

Request a Quote

Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) in an industrial setting
Illustrative image redrawn from real Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) product references — not a photograph of stocked items.

Specifications

Low head socket cap screws cut the head height to roughly two-thirds of the standard B18.3 head so the screw fits where a full-height cap screw would foul: shallow pockets, sliding covers, tooling plates stacked close together. The collected chart tabulates the ladder where the variant actually exists — six sizes, #8 through 1/2 — each with body and head diameter max/min pairs, head height, hex socket and key engagement, plus the two figures that separate this variant from the standard head: minimum tensile and the tightening torque. At 1/4 the low head runs 0.375 in head diameter (same as standard) on a 0.127 in height against the standard 0.250 — and its 5,250 lb minimum tensile and 77.9 in-lb torque sit below the standard head's 5,725 lb / 200 in-lb, the mechanical consequence of the thinner wall between socket and head. That trade is the whole selection argument: buy clearance with preload. The source states the same boundary the standard does — low heads cannot carry the same preload as standard heads of the same size — so joints designed around standard cap-screw torque tables do not transfer to this variant without re-checking. The ladder stops at #8 and 1/2 because that is where the variant's product line runs; below #8 or above 1/2, the standard head is the offering, per RFQ for anything unusual.

Standard ASME B18.3 — low head socket cap screws, inch series; 6-size ladder #8 through 1/2, alloy steel
Per-row data (in) Body diameter max/min, head diameter max/min, head height, hex socket, key engagement — 1/4: body 0.2500/0.2435, head 0.375/0.369, height 0.127/0.121, socket 0.125
Mechanical (alloy) Tensile lbs min and tightening torque per size — 1/4: 5,250 lb UNRC / 6,000 lb UNRF, 77.9 in-lb; 1/2: 23,400 / 26,350 lb, 615.0 in-lb
Preload boundary Reduced head height ⇒ lower allowable preload than the standard head of the same size — do not reuse standard-head torque tables (flagged on the page)
Size coverage #8 to 1/2 only in the collected chart; other sizes per RFQ
ASME B18.3 low head socket cap screws — dimensions and mechanical properties, #8 through 1/2 (inch, alloy)Dimensions in inches; tensile in pounds minimum; tightening torque in inch-pounds. Column labels follow the flattened source grid: basic screw diameter prints a single max, body diameter a max/min pair, head diameter and height max/min pairs, hex socket max and key engagement min, then tensile UNRC/UNRF and one torque column.
SizeBasic Screw Dia. (D) MaxBody Dia. (F) MaxBody Dia. (F) MinHead Dia. (A) MaxHead Dia. (A) MinHead Height (H) MaxHead Height (H) MinHex Socket (J) MaxKey Engagement (T) MinTensile UNRC (lbs min)Tensile UNRF (lbs min)Tightening Torque (in.-lbs)
80.16400.16400.15850.2700.2650.0850.0790.0780.0602,3102,44019.4
100.19000.19000.18400.3120.3070.0980.0920.0940.0722,8903,30033.5
1/40.25000.25000.24350.3750.3690.1270.1210.1250.0945,2506,00077.9
5/160.31250.31250.30530.4370.4310.1580.1520.1560.1108,6509,550156.0
3/80.37500.37500.36780.5620.5560.1920.1820.1880.11512,80014,450273.0
1/20.50000.50000.49190.7500.7430.2540.2440.2500.15123,40026,350615.0
  • Row 1 (8): Ladder covers #8 through 1/2 only — the source chart does not extend the low-head ladder below #8 or above 1/2 in; larger sizes are per RFQ, not extrapolated.
ASME B18.3 low head socket cap screws — tolerance on length (inch)Negative tolerance applied to the stated nominal screw length.
Thread Length GroupUp to 1 in.Over 1 in. to 2-1/2 in.
Up to 1" (Inclusive)Over 1" - 2-1/2" (Inclusive)
0 thru 3/8-.03-.04
1/2-.03-.06
Low head socket cap screws, inch series - tensile, shear and seating torqueStrengths in pounds (min.); seating torque in inch-pounds. "to 1"" marks the guide's shear figure for lengths up to 1 inch. The guide's notes, carried verbatim: material ASTM A574 alloy steel; hardness Rc 38–43; tensile strength 170,000 psi min.; yield strength 150,000 psi min.; threads class 3A UNRC and UNRF.
Nom. sizeUNRC tensile (lbs. min.)UNRF tensile (lbs. min.)UNRC shear to 1" (lbs.)UNRF shear to 1" (lbs.)Recommended seating torque (inch-lbs.)
#82,3802,5001,4501,57025
#102,9803,4001,7002,14035
1/4"5,4106,1803,0903,90080
5/16"8,9109,8704,9306,210157
3/8"13,20014,9007,4509,400278
1/2"24,10027,20013,60017,100667

Materials

  • Alloy steel, quenched and tempered (~170,000 psi tensile class per the source); the chart is geometry data — state finish and environment at RFQ

Ordering & documentation

Documents

Shipments of Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for low head socket cap screw dimensions — asme b18.3 inch ladder (#8 to 1/2, alloy) is 10,000 pieces (applies to the standard sizes and finishes for low head socket cap screw dimensions — asme b18.3 inch ladder (#8 to 1/2, alloy); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for low head socket cap screw dimensions — asme b18.3 inch ladder (#8 to 1/2, alloy) run 3–7 days. Quantities or variants of low head socket cap screw dimensions — asme b18.3 inch ladder (#8 to 1/2, alloy) outside the standard range are confirmed at quotation.

Storage & shipping

Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store low head socket cap screw dimensions — asme b18.3 inch ladder (#8 to 1/2, alloy) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How much strength does the low head actually give up, and how do I spec it without under-torquing the joint?

Compare the two ladders at the same size and the cost of the clearance is visible: at 1/4 the low head carries 5,250 lb minimum tensile and 77.9 in-lb of tightening torque against the standard head's 5,725 lb and 200 in-lb — roughly 8% of strength but under half the allowable torque, because torque limits head failure (socket wall strip-out), not thread strength. That is the practical rule: the thread is nearly as strong as a standard screw, but the head is not, so the preload you can develop drops accordingly. Spec it by stating the size and letting the low-head torque column govern the assembly instruction — do not port the standard-head torque value, which will overload the reduced head. Choose this variant when the head height envelope genuinely binds (stacked plates, sliding hardware, shallow counterbores); when height is free, the standard head buys more preload for the same thread. The collected chart covers #8–1/2 in alloy only — stainless low heads, fine-thread torque figures and larger sizes are not tabulated, so they come back as RFQ answers rather than chart lookups.

What is the MOQ and lead time for socket screws referenced by these charts?

The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Confirm the exact schedule against quantity, size mix and finish at quotation.

What is the MOQ and lead time for Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy)?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) state?

State the full designation (ASME B18.3), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy) inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your Low Head Socket Cap Screw Dimensions — ASME B18.3 Inch Ladder (#8 to 1/2, Alloy)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.