ISO 15480 Thread Forming Screws for Metric ISO Threads
ISO 15480 thread forming screws for metric ISO threads M3 to M6 — screws that roll a standard-pitch metric thread into a prepared hole, with the collected d2/k/m (PZ-Bit) attribute rows.
Last updated: 2026-11
Specifications
Thread forming screws for metric ISO threads roll (not cut) a standard-pitch metric thread into a properly sized pilot hole, so the mating thread reads ISO form and the fastener can be removed and refitted into the same boss without chewing it — the usual choice for thermoplastic housings and die-cast bosses that must survive service. The collected page is deliberately thin: four attribute rows over M 3 – M 6 — head diameter d2 (5,6 → 11 mm), head height k (1,65 → 3) and the Pozidriv bit row m (PZ-Bit): PZ 1 at M 3, PZ 2 at M 4/M 5, PZ 3 at M 6. Pilot-hole sizing and thread-forming torque are not tabulated by the collected specification — those depend on the boss material, and we quote them per RFQ against your host drawing. Property class and finish likewise per RFQ.
| Standard | ISO 15480 — thread forming screws for metric ISO threads (rolled, reusable form) |
|---|---|
| Size range | M 3 – M 6 in the collected attribute rows |
| Head geometry | d2 max.: 5,6 (M 3) → 11 mm (M 6); k: 1,65 → 3 |
| Drive | Pozidriv per the m (PZ-Bit) row: PZ 1 / PZ 2 / PZ 2 / PZ 3 across M 3 – M 6 |
| Not tabulated | Pilot-hole ladder, forming torque, length range — depend on the host boss material, per RFQ |
| Material / class / finish | Not tabulated by the collected specification — per RFQ |
| d | M 3 | M 4 | M 5 | M 6 |
|---|---|---|---|---|
| d2 | 5,6 | 8 | 9,2 | 11 |
| k | 1,65 | 2,2 | 2,5 | 3 |
| m (PZ-Bit) | PZ 1 | PZ 2 | PZ 2 | PZ 3 |
Materials
- Material and class specified per RFQ — thread forming into plastics and die-castings commonly runs case-hardened steel; state the host boss material, wall thickness and reusability requirement at quotation, since the pilot-hole size and forming torque follow from them
Ordering & documentation
Documents
Shipments of ISO 15480 Thread Forming Screws for Metric ISO Threads are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 15480 Thread Forming Screws for Metric ISO Threads orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 15480 Thread Forming Screws for Metric ISO Threads), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for iso 15480 thread forming screws for metric iso threads is 10,000 pieces (applies to the standard sizes and finishes for iso 15480 thread forming screws for metric iso threads; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 15480 thread forming screws for metric iso threads run 3–7 days. Quantities or variants of iso 15480 thread forming screws for metric iso threads outside the standard range are confirmed at quotation.
Storage & shipping
ISO 15480 Thread Forming Screws for Metric ISO Threads are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 15480 thread forming screws for metric iso threads dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Thread forming (ISO 15480) or thread cutting — which screw for my plastic boss?
Reuse and chip control. A forming screw rolls the boss material aside without removing it: no chips to pack the boss or escape into the assembly, and a work-hardened mating thread that typically survives several refits. A thread-cutting screw is faster to drive and gentler on very brittle bosses, but it removes material and wears out on reassembly. The collected ISO 15480 rows are deliberately minimal (d2, k and the Pozidriv drive per size, M 3 – M 6) because the numbers that actually decide the joint — pilot-hole diameter and seating torque — belong to the boss material, not the screw standard: quote them per RFQ against your housing drawing. One practical note: Pozidriv (PZ), not Phillips — the bit row is explicit (PZ 1 at M 3 up to PZ 3 at M 6) and the two drive families are not interchangeable at torque.
What is the MOQ and lead time for ISO 15480 Thread Forming Screws for Metric ISO Threads?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ISO 15480 Thread Forming Screws for Metric ISO Threads state?
State the full designation (ISO 15480), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 15480 Thread Forming Screws for Metric ISO Threads inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your ISO 15480 Thread Forming Screws for Metric ISO Threads
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support