DIN 564 Set Screws, Half Dog Point and Flat Cone Point
DIN 564 hexagon set screws with small hexagon, half dog point and flat cone point, M6 to M36: point forms z2/z5, head geometry and the commercial length ladder to 200 mm.
Last updated: 2026-11
Specifications
DIN 564 is the twin-point companion to DIN 561: one screw geometry, two points — the half dog z2 (nom=min 18 at M36) that half-locates in a groove or hole edge, and the flat (truncated) cone z5 (10 at M36) that centers without the full bite of a sharp cone. The collected 02/1995-edition table runs M6 to M36 with P, dp nom=max, e min, k nom and the small hexagon s nom=max (46 at M36), plus the commercial length ladder 12 to 200 mm with its mass table. The half dog is the maintenance-friendly point: it slides into a slot for quick positioning of interchangeable parts (changeover tooling, shaft collars adjusted in service), while the flat cone suits soft shafts where a sharp point would mushroom. Both points come on the same head and thread, so the choice is a point-ordering decision, not a redesign.
| Standard / scope | DIN 564 hexagon set screws, small hexagon, half dog point and flat cone point — M6 to M36, edition 02/1995 (supersedes 02/1985) |
|---|---|
| Point forms | Half dog z2 nom=min per size (18 at M36); flat cone z5 (10 at M36) — order the point form explicitly, both exist under the standard |
| Thread / head | P, dp nom=max, k nom per size; small hexagon s nom=max 46 / e min 51.28 at M36 |
| Commercial lengths l | Ladder 12 to 200 mm across M6–M36; approximate mass per 1000 pcs (ρ=7,85 kg/dm³) tabulated |
| Not tabulated | Property class (45H-type), finish, point hardness — per RFQ |
| d thread size | P | dp nom=max | e min | k nom | s nom=max | z2 nom=min | z5 | ||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 6 | 1 | 4 | 8.79 | 5 | 8 | 3 | 1.75 | ||||
| M 8 | 1.25 | 5.5 | 11.05 | 6 | 10 | 4 | 2.5 | ||||
| M 10 | 1.5 | 7 | 14.38 | 7 | 13 | 5 | 3 | ||||
| M 12 | 1.75 | 8.5 | 17.77 | 9 | 16 | 6 | 3.5 | ||||
| M 16 | 2 | 12 | 19.92 | 11 | 18 | 8 | 4.5 | ||||
| M 20 | 2.5 | 15 | 26.75 | 14 | 24 | 10 | 5 | ||||
| M 24 | 3 | 18 | 33.53 | 17 | 30 | 12 | 6 | ||||
| M 30 | 3.5 | 23 | 39.98 | 21 | 36 | 15 | 8 | ||||
| M 36 | 4 | 28 | 51.28 | 25 | 46 | 18 | 10 |
- Source spanning title row carried verbatim: "Dimensions in mm - source DIN 564".
- Edition row carried from the source grid: "Publication date 02 - 1995 - supersedes DIN 564 02 - 1985".
- Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (12/8) — grid padded empty; per-row pre-pad widths: 12,12,8,8,8,8,8,8,8,8,8,8.
| d thread size | M6 | M8 | M10 | M12 | M16 | M20 | M24 | M30 | M36 |
|---|---|---|---|---|---|---|---|---|---|
| nominal length l | |||||||||
| 12 | 3.93 | ||||||||
| 14 | 4.27 | ||||||||
| 16 | 4.61 | 8.30 | |||||||
| 18 | 4.96 | 8.94 | |||||||
| 20 | 5.32 | 9.54 | 16.5 | ||||||
| 25 | 6.11 | 11.1 | 18.9 | 33.1 | |||||
| 30 | 7.06 | 12.7 | 21.4 | 36.6 | 60.3 | ||||
| 35 | 14.2 | 23.9 | 40.5 | 66.9 | |||||
| 40 | 15.8 | 26.4 | 43.8 | 73.5 | 128 | ||||
| 45 | 28.8 | 47.4 | 80.1 | 139 | 227 | ||||
| 50 | 31.3 | 51 | 86.6 | 150 | 243 | ||||
| 60 | 58.1 | 99.8 | 172 | 275 | 432 | ||||
| 70 | 65.3 | 113 | 194 | 307 | 479 | ||||
| 80 | 126 | 216 | 339 | 526 | 850 | ||||
| 90 | 139 | 238 | 371 | 573 | 918 | ||||
| 100 | 260 | 403 | 620 | 986 | |||||
| 120 | 467 | 713 | 1120 | ||||||
| 140 | 807 | 1260 | |||||||
| 160 | 901 | 1390 | |||||||
| 180 | 1530 | ||||||||
| 200 | 1670 |
- Source spanning title row carried verbatim: "DIN 564 1995 - Approximate mass, in kg x1000 pcs, (ρ=7,85 kg/dm 3 ) - commercial items".
- Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (10/1/2/3/4/5/6/7/8/9) — grid padded empty; per-row pre-pad widths: 10,10,1,2,2,3,3,4,5,6,6,7,8,8,9,9,10,10,10,10,10,10,10,10.
Materials
- Same discipline as the DIN 561 series: hardened class 45H steel with hardened point as default, zinc or black finish, A2/A4 stainless where corrosion rules. Say which point form the order is for — z2 or z5 — because the two share a drawing number otherwise; and for soft or aluminum shafts ask for the flat cone z5, whose truncated tip spreads the load instead of digging
Ordering & documentation
Documents
Shipments of DIN 564 Set Screws, Half Dog Point and Flat Cone Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 564 Set Screws, Half Dog Point and Flat Cone Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 564 Set Screws, Half Dog Point and Flat Cone Point), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 564 set screws, half dog point and flat cone point is 10,000 pieces (applies to the standard sizes and finishes for din 564 set screws, half dog point and flat cone point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 564 set screws, half dog point and flat cone point run 3–7 days. Quantities or variants of din 564 set screws, half dog point and flat cone point outside the standard range are confirmed at quotation.
Storage & shipping
DIN 564 Set Screws, Half Dog Point and Flat Cone Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 564 set screws, half dog point and flat cone point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
What is the practical difference between the half dog (z2) and flat cone (z5) points?
The half dog is a locating point: a cylindrical tip of diameter z2 that engages a groove, slot or hole edge and positively stops rotation — the part can be backed off and re-engaged in the same place every time, which is why it owns changeover fixtures. The flat cone is a centering point: its truncated tip finds a dimple and centers the part under clamp load without the deep penetration of a sharp cone, kinder to soft shafts and to parts that will be removed. If the joint needs positive indexing, order z2 and machine the groove; if it needs repeatable clamping on a finished surface, z5 and a light center drill.
How does DIN 564 relate to the larger DIN 561 series?
They share the small-hexagon head system and the same 1995 edition family, but the size ranges differ — DIN 561 (registered separately) runs dog points up to M56 with commercial lengths to 300 mm, while DIN 564 covers the twin-point forms M6 to M36 to 200 mm. In practice: single-purpose permanent location at large size goes 561 full dog; anything needing the half dog or the flat cone comes from 564. Head wrench sizes differ between the standards at the same thread, so check the s column against your wrench stock — the small-hex system is not the standard hex series.
What is the MOQ and lead time for DIN 564 Set Screws, Half Dog Point and Flat Cone Point?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 564 Set Screws, Half Dog Point and Flat Cone Point state?
State the full designation (DIN 564 Set Screws, Half Dog Point and Flat Cone Point), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 564 Set Screws, Half Dog Point and Flat Cone Point inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 564 Set Screws, Half Dog Point and Flat Cone Point
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support