ISO 7435 Slotted Set Screws, Long Cone Point

ISO 7435 slotted set screws with long cone point, M1,6 to M12 — the sibling of ISO 7434 with the extended point (z rows) for deep-seated locating, with two verbatim source quirks flagged (n max 0,26 at M 8, t max 10,5 at M 3).

Last updated: 2026-11

Request a Quote

ISO 7435 Slotted Set Screws, Long Cone Point in an industrial setting
Illustrative image redrawn from real ISO 7435 Slotted Set Screws, Long Cone Point product references — not a photograph of stocked items.

Specifications

Where the ordinary cone point just marks, the long cone point reaches: ISO 7435's extended point (the z rows, 0,8 → 6 min / 1,05 → 6,3 max across M 1,6 → M 12) seats into a drilled recess or locates a part set back in a bore, keeping the clamping face of the screw shank clear of the component — useful in chuck and arbor work, and anywhere the point must engage before the shank does. The collected grid runs M 1,6 → M 12: thread P 0,35 → 1,75, point diameter dp 0,8 → 8,5 (max) / 0,55 → 8,14 (min), slot n 0,25 → 2 nominal, recess t 0,56 → 2,8 min, and the mass ladder across 20 nominal lengths l 2 → 60. Three verbatim quirks to note before quoting: the source titles the page "Slotted set screws and pins", but the tabulated columns are a slotted set-screw attribute set (dp/n/t/z) — the tension is disclosed rather than resolved; n max at M 8 prints 0,26 against the ,06 pattern; t max at M 3 prints 10,5 against the 1,05 step of its neighbours. All three are flagged in the table — confirm those cells per RFQ if your order lands on M 8 or M 3. Material, hardness and finish are not tabulated — per RFQ; lead time, MOQ and pricing: contact for confirmation.

Standard ISO 7435 — slotted set screws, long cone point
Size range M 1,6 – M 12 in the collected rows (M3,5 in brackets per the source series)
Point long cone point; dp max 0,8 → 8,5 / min 0,55 → 8,14; z min 0,8 → 6 / max 1,05 → 6,3
Slot (n) nominal 0,25 → 2; max 0,31 → 2,06 with the M 8 quirk flagged; min 0,45 → 2,31
Recess (t) min 0,56 → 2,8; max 0,74 → 3,6 with the M 3 quirk flagged
Length ladder l 2 – 60 (20 nominal lengths) with mass kg/1000pcs
Not tabulated Material, hardness, finish — per RFQ; lead time, MOQ and pricing: contact for confirmation
Designation note ISO 7434 (cone point, shorter) and ISO 7436 (cup point) are separate designations already in this catalog — order by drawing designation
ISO 7435 slotted set screws (long cone point) - attribute rows and mass ladderGeometry rows in millimetres under the source's "Thread d" header; the lower band is the source's mass ladder (weight kg/1000pcs). The source titles the page "Slotted set screws and pins"; the tabulated columns (dp, n, t, z over a slotted set-screw attribute set) are carried as printed — see the page note on the title tension. df is the source's "Thread - core diameter" prose row (merged cell carried once). z = point-length rows per the source; blank = not tabulated.
AttributeQualifierSub-qualifierM 1,6M 2M 2,5M 3(M3,5)M 4M 5M 6M 8M 10M 12
PP0,350,40,450,50,60,70,811,251,51,75
dfdfThread - core diameterThread - core diameterThread - core diameterThread - core diameterThread - core diameterThread - core diameter
dpmax.0,811,522,22,53,545,578,5
dpmin.0,550,751,251,751,952,253,23,75,26,648,14
nNominal size0,250,40,50,60,811,21,62
nmax.0,310,460,560,660,861,060,261,662,06
nmin.0,450,60,70,811,21,511,912,31
tmin.0,560,640,720,80,961,121,281,622,42,8
tmax.0,740,840,9510,51,211,421,6322,533,6
zmin.0,811,251,51,7522,53456
zmax.1,051,251,51,7522,252,753,254,35,36,3
llWeight kg/1000pcsWeight kg/1000pcsWeight kg/1000pcsWeight kg/1000pcsWeight kg/1000pcsWeight kg/1000pcs
Nominal sizemin.max.
21,82,2
2,52,32,7
32,83,20,04
43,754,250,060,08
54,755,250,080,110,170,22
65,76,30,10,140,210,280,34
87,78,30,20,290,390,50,761,02
109,710,30,380,50,661,011,422,5
1211,612,40,470,610,821,261,823,14,35
(14)13,614,40,720,981,52,223,75,35
1615,616,40,831,141,72,624,36,35
2019,620,43,425,58,35
2524,625,4710,9
3029,630,413,4
3534,535,515,9
4039,540,5
4544,545,5
5049,550,5
5554,455,6
6059,460,6
  • Row 6 (n): n max. at M 8 prints 0,26 against the ,06 pattern (0,31 / 0,46 / 0,56 / 0,66 / 0,86 / 1,06 / ...) — carried verbatim; confirm M 8 slot max per RFQ.
  • Row 9 (t): t max. at M 3 prints 10,5 against the 1,05 step of its neighbours — carried verbatim; confirm M 3 recess depth per RFQ.
  • Row 16 (3): source order quirk: the n rows print Nominal size / max. / min. (min. after max.), unlike the min./max. order elsewhere — carried in source order.

Materials

  • Material and finish specified per RFQ — long-cone set screws commonly run hardened alloy steel; state the bore/recess the point must seat in (the z point length has to have somewhere to go) and whether the marked surface is acceptable at quotation

Ordering & documentation

Documents

Shipments of ISO 7435 Slotted Set Screws, Long Cone Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 7435 Slotted Set Screws, Long Cone Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ISO 7435 Slotted Set Screws, Long Cone Point), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for iso 7435 slotted set screws, long cone point is 10,000 pieces (applies to the standard sizes and finishes for iso 7435 slotted set screws, long cone point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 7435 slotted set screws, long cone point run 3–7 days. Quantities or variants of iso 7435 slotted set screws, long cone point outside the standard range are confirmed at quotation.

Storage & shipping

ISO 7435 Slotted Set Screws, Long Cone Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 7435 slotted set screws, long cone point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

The source calls this "Slotted set screws and pins" — is it a screw or a pin, and when is the long point worth specifying?

It is a set screw — the collected columns (dp point diameter, n slot, t recess depth, z point length over a length ladder with masses) are a set-screw attribute set, and the "and pins" in the source title is its wording, disclosed here rather than silently adopted. The designation itself is unambiguous. On when the long point wins over the ISO 7434 ordinary cone: specify the long cone when the point must engage a pre-drilled recess or reach past a shoulder — the z row is the extra point length that does that engaging (0,8 → 6 across the range, so the mating recess depth must be planned to match), while the shorter ISO 7434 point is the right choice for direct-into-surface indexing where there is no recess to seat in. Two cells on this page are verbatim-flagged in the table (n max 0,26 at M 8, t max 10,5 at M 3) because they break the numeric pattern of their rows; if your order lands on those sizes, confirm the printed values per RFQ before quoting the drawing. Sibling designations ISO 7434 and ISO 7436 are in this catalog with their own ladders.

What is the MOQ and lead time for ISO 7435 Slotted Set Screws, Long Cone Point?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ISO 7435 Slotted Set Screws, Long Cone Point state?

State the full designation (ISO 7435), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ISO 7435 Slotted Set Screws, Long Cone Point inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your ISO 7435 Slotted Set Screws, Long Cone Point
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.