DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess)
Self-drilling screws per DIN 7504 form P — countersunk head with Phillips recess, zinc plated steel — running Ø 3.5 to 5.5 mm × length 9.5 to 70 mm, with per-size max drilling capacity (2–5 mm) and clamping range, seating flush in a mating countersink.
Last updated: 2026-11
Specifications
The DIN 7504-P pairs the one-operation drill-and-fasten point with a countersunk head, for panels where a proud head is not acceptable: the head seats flush in a mating countersink while the point still drills, taps and clamps without a prepared hole. The collected line-page table runs the form across Ø 3.5, 3.9, 4.2, 4.8 and 5.5 mm with lengths from 9.5 to 70 mm, printing the same drilling-capacity ladder as the pan-head N form — 2 mm at Ø 3.5/3.9, 3 mm at 4.2, 4 mm at 4.8, 5 mm at 5.5 — with clamping ranges of 4–61 mm across the length ladder. At Ø 4.8 the ladder runs thirteen to seventy millimetres; at Ø 5.5 the collected rows are 19, 32, 38 and 50 mm (clamping 9–40 mm). Drive is Phillips by diameter (PH1/PH2/PH3), and the flush finish depends on the mating countersink being cut to match — the same seating rule as the DIN 7982 countersunk tapping screw, with the drill point added. The collected tables are metric; the inch TEK point-number series is not carried by this source and is not stated here.
| Standard | DIN 7504 form P — self-drilling screw, countersunk head with Phillips recess |
|---|---|
| Size range | Ø 3.5 – 5.5 mm × length 9.5 – 70 mm (collected table) |
| Max drilling capacity | 2 mm (Ø 3.5/3.9) · 3 mm (Ø 4.2) · 4 mm (Ø 4.8) · 5 mm (Ø 5.5) |
| Clamping range | 4 – 61 mm across the collected length ladder, per size and length |
| Drive | PH1 (Ø 3.5/3.9), PH2 (Ø 4.2/4.8), PH3 (Ø 5.5), as printed per row |
| Seating | Flush in a mating countersink — confirm the countersink with the screw |
| Finish | Zinc plated steel, as printed on the collected line page |
| Case hardness | Rockwell C52-58 minimum (C), per the collected self-drilling hardness table |
| Core hardness (after tempering) | Rockwell C32-40, per the collected self-drilling hardness table |
| Material | AISI 1016-1024 or equivalent steel, per the collected self-drilling hardness table |
| Materials | Zinc plated carbon steel (case hardened per the collected hardness row); stainless and other finishes confirmed at quotation |
| Ø — screw diameter (mm) | l — length (mm) | Max drilling capacity (mm) | Clamping range (mm) | Drive bit (as printed) |
|---|---|---|---|---|
| 3.5 | 9.5 | 2 | 5 | PH1 |
| 3.5 | 13 | 2 | 8 | PH1 |
| 3.5 | 16 | 2 | 11 | PH1 |
| 3.5 | 19 | 2 | 14 | PH1 |
| 3.5 | 22 | 2 | 17 | PH1 |
| 3.5 | 25 | 2 | 20 | PH1 |
| 3.9 | 13 | 2 | 7 | PH1 |
| 3.9 | 16 | 2 | 10 | PH1 |
| 3.9 | 19 | 2 | 14 | PH1 |
| 3.9 | 22 | 2 | 16 | PH1 |
| 3.9 | 25 | 2 | 19 | PH1 |
| 3.9 | 32 | 2 | 26 | PH1 |
| 4.2 | 13 | 3 | 6 | PH2 |
| 4.2 | 16 | 3 | 9 | PH2 |
| 4.2 | 19 | 3 | 12 | PH2 |
| 4.2 | 22 | 3 | 15 | PH2 |
| 4.2 | 25 | 3 | 18 | PH2 |
| 4.2 | 32 | 3 | 25 | PH2 |
| 4.2 | 38 | 3 | 31 | PH2 |
| 4.8 | 13 | 4 | 4 | PH2 |
| 4.8 | 16 | 4 | 7 | PH2 |
| 4.8 | 19 | 4 | 10 | PH2 |
| 4.8 | 22 | 4 | 13 | PH2 |
| 4.8 | 25 | 4 | 16 | PH2 |
| 4.8 | 32 | 4 | 23 | PH2 |
| 4.8 | 38 | 4 | 29 | PH2 |
| 4.8 | 45 | 4 | 36 | PH2 |
| 4.8 | 50 | 4 | 41 | PH2 |
| 4.8 | 60 | 4 | 51 | PH2 |
| 4.8 | 70 | 4 | 61 | PH2 |
| 5.5 | 19 | 5 | 9 | PH3 |
| 5.5 | 32 | 5 | 21 | PH3 |
| 5.5 | 38 | 5 | 27 | PH3 |
| 5.5 | 50 | 5 | 40 | PH3 |
Materials
- Zinc plated carbon steel (case hardened per the collected hardness row); stainless and other finishes confirmed at quotation
Ordering & documentation
Documents
Shipments of DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 7504-p self-drilling screws (countersunk head, phillips recess) is 10,000 pieces (applies to the standard sizes and finishes for din 7504-p self-drilling screws (countersunk head, phillips recess); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 7504-p self-drilling screws (countersunk head, phillips recess) run 3–7 days. Quantities or variants of din 7504-p self-drilling screws (countersunk head, phillips recess) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 7504-p self-drilling screws (countersunk head, phillips recess) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When is a countersunk self-drilling screw the right call?
Where the drill-and-fasten operation and a flush surface are both required — thin panel-to-frame joints in ventilations, cabins, partition and insulation work where a proud pan or hex head would foul the next layer, a sliding part or the finished face. The trade is seating tolerance: a countersunk head only looks flush if the mating countersink is cut to match, so confirm the countersink with the screw, and remember the flush head gives up the high-torque capability of the serrated hex form (7504-K). The drilling-capacity ladder is unchanged — 2 to 5 mm across the collected diameters.
Does the countersunk head change the drilling figures?
No. The collected table prints the same per-diameter drilling capacity as the other DIN 7504 forms — 2 mm at Ø 3.5/3.9, 3 mm at 4.2, 4 mm at 4.8 and 5 mm at 5.5 — because the capacity belongs to the point, not the head. What the head changes is length measurement and seating: the countersink must be matched, and the clamping range still decides engagement. Read the length ladder per row rather than assuming the pan-head page transfers — the collected P rows stop at 70 mm and the Ø 5.5 selection is narrower (19/32/38/50 mm).
What is the MOQ and lead time for these self-drilling screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Self-drilling screws in the common DIN 7504 sizes are widely stocked — confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for self-drilling (TEK) screws state?
State the standard designation and form letter (for example DIN 7504 N or DIN 7504 K), screw diameter and length, the total thickness and type of the metal being drilled through and clamped, head form and drive, finish (for example zinc plated), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 7504-P Self-Drilling Screws (Countersunk Head, Phillips Recess)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support