ISO 1482 Slotted Countersunk Head Tapping Screws
ISO 1482 slotted countersunk head tapping screws ST2,2 to ST6,3 — the flush-finish sheet-metal screw for pre-countersunk holes, with the collected geometry ladder (dk/k/n/r/t) and the per-length mass ladder.
Last updated: 2026-11
Specifications
ISO 1482 takes the slotted tapping screw flush: a 90-degree countersunk head that sits at or below the sheet surface once the hole is countersunk to match. That flush is the point wherever a sliding workpiece, a wiper, or a second panel passes over the fastener — the head leaves nothing to catch. The collected ladder runs ST2,2 to ST6,3 with the head diameter dk in its nominal=max./min. pair (4,3/4 at ST2,2 up to 12,4/11,97 at ST6,3), the approximate head height k, the slot triple n nominal/min./max., the countersink edge radius r (0,8 → 2,4 — larger than the pan head's, because the edge blends into the countersink cone), and the slot-depth t min./max. pair. The length ladder runs l 6,5 to 38 with Type C/F limits and the source's approximate mass columns per thread. One verbatim print defect is flagged: the slot nominal n at ST4,8 reads 12 against the sibling progression (0,6 → 1,6) — a lost decimal point; read that cell per RFQ if the slot sizing matters. Countersinking discipline: the hole needs both the clearance pilot and the 90-degree cone, cut deep enough that the head seats on the cone, not the edge. Property class, material and finish are not tabulated — per RFQ.
| Standard | ISO 1482 — slotted countersunk head tapping screws |
|---|---|
| Size range | ST2,2 – ST6,3; parenthesised (ST3,9) is the source's non-preferred marking |
| Head diameter | dk nominal=max. 4,3 → 12,4 mm (min. 4 → 11,97) |
| Slot | n nominal 0,6 → 1,6 (ST4,8 cell prints 12 verbatim — flagged); t min. 0,4 → 1,2, max. 0,6 → 1,75 |
| Countersink radius | r max. 0,8 → 2,4 mm per size |
| Length ladder | l 6,5 – 38 with Type C/F min./max. limits and approximate mass per thread |
| Material / finish | Not tabulated by the collected specification — per RFQ |
| Attribute | Limit | ST2,2 | ST2,9 | ST3,5 | (ST3,9) | ST4,2 | ST4,8 | ST5,5 | ST6,3 |
|---|---|---|---|---|---|---|---|---|---|
| P | 0,8 | 1,1 | 1,3 | 1,3 | 1,4 | 1,6 | 1,8 | 1,8 | |
| a | max. | 0,8 | 1,1 | 1,3 | 1,3 | 1,4 | 1,6 | 1,8 | 1,8 |
| dk | nominal=max. | 4,3 | 5,5 | 6,8 | 7,5 | 8,1 | 9,5 | 10,8 | 12,4 |
| dk | min. | 4 | 5,2 | 6,44 | 7,14 | 7,74 | 9,14 | 10,37 | 11,97 |
| k | approx. | 1,3 | 1,7 | 2,1 | 2,3 | 2,5 | 3 | 3,4 | 3,8 |
| n | nominal | 0,6 | 0,8 | 1 | 1 | 1,2 | 12 | 1,6 | 1,6 |
| n | min. | 0,66 | 0,86 | 1,06 | 1,06 | 1,26 | 1,26 | 1,66 | 1,66 |
| n | max. | 0,8 | 1 | 1,2 | 1,2 | 1,51 | 1,51 | 1,91 | 1,91 |
| r | max. | 0,8 | 1,1 | 1,4 | 1,5 | 1,6 | 1,9 | 2,1 | 2,4 |
| t | min. | 0,4 | 0,5 | 0,6 | 0,7 | 0,75 | 0,85 | 1 | 1,2 |
| t | max. | 0,6 | 0,75 | 0,95 | 1,05 | 1,15 | 1,35 | 1,5 | 1,75 |
| y max. | Type C | 2 | 2,6 | 3,2 | 3,5 | 3,7 | 4,3 | 5 | 6 |
| y max. | Type F | 1,6 | 2,1 | 2,5 | 2,7 | 2,8 | 3,2 | 3,6 | 3,6 |
- Row 6 (n): n nominal at ST4,8 prints 12 against the sibling progression 0,6/0,8/1/1/1,2/…/1,6/1,6 — a lost decimal point suspected. Carried verbatim, not normalized.
| l nominal | Type C min. | Type C max. | Type F min. | Type F max. | ST2,2 | ST2,9 | ST3,5 | (ST3,9) | ST4,2 | ST4,8 | ST5,5 | ST6,3 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 6,5 | 5,7 | 7,3 | 5,7 | 6,5 | 0,14 | 0,242 | ||||||
| 9,5 | 8,7 | 10,3 | 8,7 | 9,5 | 0,2 | 0,35 | 0,548 | 0,658 | 0,775 | 1,1 | ||
| 13 | 12,2 | 13,8 | 12,2 | 13 | 0,27 | 0,476 | 0,722 | 0,88 | 1,02 | 1,45 | 2,11 | 2,53 |
| 16 | 15,2 | 16,8 | 15,2 | 16 | 0,33 | 0,584 | 0,871 | 1,07 | 1,23 | 1,75 | 2,49 | 3,07 |
| 19 | 18,2 | 19,8 | 18,2 | 19 | 0,692 | 1,02 | 1,26 | 1,44 | 2,05 | 2,87 | 3,61 | |
| 22 | 21,2 | 22,8 | 20,7 | 22 | 1,17 | 1,45 | 1,65 | 2,35 | 3,26 | 4,15 | ||
| 25 | 24,2 | 25,8 | 23,7 | 25 | 1,32 | 1,64 | 1,86 | 2,65 | 3,65 | 4,69 | ||
| 32 | 30,7 | 33,3 | 30,7 | 32 | 2,35 | 3,35 | 4,56 | 5,95 | ||||
| 38 | 36,7 | 39,3 | 36,7 | 38 | 3,95 | 5,34 | 7,03 |
Materials
- Material and finish specified per RFQ — state the host sheet thickness (the countersink cone eats into it; thin sheet needs a formed rather than cut countersink) and any plating requirement
Ordering & documentation
Documents
Shipments of ISO 1482 Slotted Countersunk Head Tapping Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 1482 Slotted Countersunk Head Tapping Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 1482 Slotted Countersunk Head Tapping Screws), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for iso 1482 slotted countersunk head tapping screws is 10,000 pieces (applies to the standard sizes and finishes for iso 1482 slotted countersunk head tapping screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 1482 slotted countersunk head tapping screws run 3–7 days. Quantities or variants of iso 1482 slotted countersunk head tapping screws outside the standard range are confirmed at quotation.
Storage & shipping
ISO 1482 Slotted Countersunk Head Tapping Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 1482 slotted countersunk head tapping screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Countersunk (ISO 1482) or raised countersunk (ISO 1483) — what changes on the sheet?
Nothing about the hole; everything about the surface. Both screws use the same head diameter ladder (dk 4,3 → 12,4 across the shared size range) and the same countersink cone, so the drilled and csk-prepped hole is interchangeable. ISO 1482 finishes flush: nothing above the sheet. ISO 1483 adds the raised crown — the collected f row (approx. 0,7 → 2 mm) — which keeps a screwdriver engaged past paint drips and gives a slightly larger driving bearing, at the cost of a proud button you must recess or accept. The raised member also carries a bigger crown radius rf (3,8 → 11,1 in its ladder vs none on the flush head). Practical read: flush where anything slides over the surface, raised where driving access and paint tolerance matter more than profile. Slot sizing, thread and length ladders otherwise match, and both carry the same verbatim ST4,8 slot-n print defect — per RFQ on that cell. Material, class and finish stay per RFQ on both.
What is the MOQ and lead time for ISO 1482 Slotted Countersunk Head Tapping Screws?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ISO 1482 Slotted Countersunk Head Tapping Screws state?
State the full designation (ISO 1482), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 1482 Slotted Countersunk Head Tapping Screws inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your ISO 1482 Slotted Countersunk Head Tapping Screws
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support