ISO 7434 Slotted Set Screws, Cone Point

ISO 7434 slotted set screws with cone point, M1 to M12 — the small-screw end of the slotted set-screw line, with the slot n / cone dt / recess t grid plus a mass ladder marked with the source's "+" trade sizes.

Last updated: 2026-11

Request a Quote

ISO 7434 Slotted Set Screws, Cone Point in an industrial setting
Illustrative image redrawn from real ISO 7434 Slotted Set Screws, Cone Point product references — not a photograph of stocked items.

Specifications

The cone point bites: unlike the flat point of ISO 4766 (already in this catalog), the coned end of a set screw digs into the opposing surface, which is what you want when the screw must positively locate a part that sees torsion — collar clamps on shafts, index stops, tooling plates — and at M1 to M12 this designation covers the instrument-and-fixture range where slotted drive still beats hex sockets (you can turn it with a plain blade, and the screw stays replaceable in the field). The collected grid runs thread P 0,25 → 1,75, cone-point diameter dt max 0,1 → 3 (dt min. is "-" across the line per the source — the point is formed to max), slot n 0,2 → 2 nominal, and the recess t 0,4 → 2,8 nominal; the lower band is the mass ladder, weight in kg per 1000 pieces across 20 nominal lengths l 2 → 60, with "+" marking the source's trade sizes. Quoting notes: dt max at M6 prints 1,5 against the 0,4/0,5/2 run of its neighbours — verbatim flagged, confirm that one cell per RFQ if your order lands on M6. Material, hardness and finish are not tabulated — per RFQ; lead time, MOQ and pricing: contact for confirmation.

Standard ISO 7434 — slotted set screws with cone point
Size range M1 – M12 in the collected rows (M3,5 in brackets per the source series)
Point cone point; dt max 0,1 → 3; dt min. "-" per the source
Slot (n) nominal 0,2 → 2 (min. 0,26 → 2,06, max. 0,4 → 2,31)
Recess (t) nominal = min. 0,4 → 2,8; max. 0,52 → 3,6
Length ladder l 2 – 60 (20 nominal lengths) with mass kg/1000; "+" = trade sizes per the source
Not tabulated Material, hardness, finish — per RFQ; lead time, MOQ and pricing: contact for confirmation
Designation note ISO 4766 (flat point, cup d above) and ISO 7436 (cup point) are separate designations already in this catalog
ISO 7434 slotted set screws with cone point - attribute rows and mass ladderGeometry rows in millimetres; the lower band is the source's mass ladder (weight kg/1000 pcs, trade sizes marked "+"). The source's two header bands are reproduced as printed: attributes in the first three columns under the source's "Thread d" header (df is the source's "Minor thread diameter" prose row — a merged source cell carried once), sizes across. "+" = trade size per the source legend; blank = not tabulated. dt min. is "-" across all sizes in the source.
AttributeQualifierSub-qualifierM1M1,2M1,4M1,6M2M2,5M3(M3,5)M4M5M6M8M10M12
PP0,250,30,350,40,450,50,60,70,811,251,51,75
dfapprox.Minor thread diameterMinor thread diameterMinor thread diameterMinor thread diameterMinor thread diameterMinor thread diameterMinor thread diameter
dtmin.-------
dtmax.0,10,120,140,160,20,250,30,350,40,51,522,53
nnominal0,20,20,250,40,50,60,811,21,62
nmin.0,260,260,310,460,560,660,861,061,261,662,06
nmax.0,40,40,450,60,70,811,21,511,912,31
tnominal =min.0,40,480,560,640,720,80,961,121,251,622,42,8
tmax.0,520,630,740,840,951,051,211,421,6322,533,6
llweight kg/1000pcsweight kg/1000pcsweight kg/1000pcsweight kg/1000pcsweight kg/1000pcsweight kg/1000pcsweight kg/1000pcs
nominalmin.max.(+ trade sizes)(+ trade sizes)(+ trade sizes)(+ trade sizes)(+ trade sizes)(+ trade sizes)(+ trade sizes)
21,82,20,0070,0110,0150,02
2,52,32,70,0090,0140,0190,026
32,83,20,0110,0170,0230,0320,0450,07
43,74,30,0150,0240,0310,0460,0650,10,13
54,75,3+0,040,060,0850,130,170,23
65,76,3+0,0740,110,160,210,290,36
87,78,3+0,140,220,290,40,510,771,04
109,710,3+0,280,370,510,671,021,442,65
1211,612,4+0,450,620,821,271,843,254,6
(14)13,614,4+0,730,971,512,243,855,6+
1615,616,40,851,121,762,644,456,6+
2019,620,4+2,253,445,658,6+
2524,625,4++11,1+
3029,630,4+13,6+
3534,535,5+16,1+
4039,540,5++
4544,545,5+
5049,550,5+
5554,455,6+
6059,460,6+
  • Row 5 (n): dt max. at M6 prints 1,5 against the 0,4 / 0,5 / 2 run at M5 / M6-neighbours (M4 0,4, M5 0,5, M8 2) — carried verbatim; confirm M6 cone diameter per RFQ.
  • Row 10 (l): the mass band header "l | weight kg/1000pcs" then "nominal | min. | max. | (+ trade sizes)" is the source's own banding, carried verbatim.

Materials

  • Material and finish specified per RFQ — small set screws commonly run hardened alloy or stainless; state the host material (the cone point mars it — use a flat point where marring matters) and the tightening tool (plain screwdriver blade width vs the n slot) at quotation

Ordering & documentation

Documents

Shipments of ISO 7434 Slotted Set Screws, Cone Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 7434 Slotted Set Screws, Cone Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ISO 7434 Slotted Set Screws, Cone Point), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for iso 7434 slotted set screws, cone point is 10,000 pieces (applies to the standard sizes and finishes for iso 7434 slotted set screws, cone point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 7434 slotted set screws, cone point run 3–7 days. Quantities or variants of iso 7434 slotted set screws, cone point outside the standard range are confirmed at quotation.

Storage & shipping

ISO 7434 Slotted Set Screws, Cone Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 7434 slotted set screws, cone point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Cone point (ISO 7434) vs cup point (ISO 7436) vs flat point (ISO 4766) — when does each win?

Point geometry decides how the set screw transfers load and what it does to the mating surface. The cone point (this page) penetrates: highest torque resistance against rotation, at the cost of marring the shaft or housing — the pick for permanent indexing, hard shafts, and joints where the mark is acceptable. The cup point (ISO 7436, also in this catalog) is the compromise: a shallow cup that bites like a punch but spreads the deformation, and it is the general-purpose default in most clamping work. The flat point (ISO 4766) contacts on a full plane: least marking, lowest rotation resistance — right against soft or finished surfaces, and for use as a plug or adjustment stop rather than a drive-catching clamp. Practically: match the designation your drawing prints; if the drawing says only "slotted set screw M4", pick by the function above and confirm the point form per RFQ. The mass ladders on the ISO 7434 and ISO 7435 pages let you price bulk orders before the confirmation step; "+" cells are trade sizes per the source legend.

What is the MOQ and lead time for ISO 7434 Slotted Set Screws, Cone Point?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ISO 7434 Slotted Set Screws, Cone Point state?

State the full designation (ISO 7434), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ISO 7434 Slotted Set Screws, Cone Point inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your ISO 7434 Slotted Set Screws, Cone Point
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.