TX34 6-Lobe Pin TX Security Grub Screw — Cone Point
Cone point 6-lobe pin security grub screw, M1.6–M24 as tabulated: min socket depth t 0.8–6.8 mm (M3 upward), socket width s 1.75–13.45 mm, tools TX6–TX60. Metric matrix marked to order 2–120 mm; steel, A2 and A4 stainless as standard; cone point gives the highest torsional holding of the grub family per the collected page. Imperial markers undefined by legend — imperial lengths at quotation.
Last updated: 2026-11
Specifications
The cone point is where the grub screw stops being gentle: a sharp tapered tip that penetrates the mating surface on installation, and the collected page credits it with the highest torsional holding power of all grub screw types. That behaviour writes its own application list — permanent settings, pivot points, adjusting screws where fine incremental changes are set and then locked, soft and hard surfaces alike. Security comes from the same two mechanisms as the rest of this batch: the centre pin in the 6-lobe socket, and the medium-security character of a drive only the matched insert bit can turn. The tabulated range spans M1.6 to M24, with socket depth and width stated from M3 (the M1.6–M2.5 columns dash — no tool claims for them), driven by TX6–TX60 tools. Like TX33, the metric availability matrix marks every tabulated cell to order from 2 mm to 120 mm — a made-to-order line, with the imperial table tabulated to 2″ but carrying markers the collected legend does not define, so imperial stays at quotation. Supply is stated in steel, A2 and A4 stainless steel as standard, with the standard caveat of the line that surface penetration is the design intent — do not specify cone point against a surface you later need undamaged.
| Designation | TX34 — cone point security grub screw (set screw), 6-lobe pin TX drive, headless, fully threaded; cone tip penetrates the contact surface for the highest torsional holding of the grub types; suited to permanent settings, pivot and adjusting duties |
|---|---|
| Thread range (tabulated) | M1.6, M2, M2.5, M3, M4, M5, M6, M8, M10, M12, M16, M20, M24 (t/s/tool tabulated from M3; M1.6–M2.5 dash — no tool claims for those sizes) |
| Min socket depth t (mm) | M3 0.8 · M4 1 · M5 1.3 · M6 1.6 · M8 2.7 · M10 2.9 · M12 3.2 · M16 4.3 · M20 5.3 · M24 6.8 |
| Socket width s (mm) | M3 1.75 · M4 2.4 · M5 2.8 · M6 3.35 · M8 4.5 · M10 5.6 · M12 6.75 · M16 8.95 · M20 11.35 · M24 13.45 |
| Tool size (collected) | TX6 (M3) · TX8 (M4) · TX10 (M5) · TX15 (M6) · TX25 (M8) · TX30 (M10) · TX40 (M12) · TX50 (M16) · TX55 (M20) · TX60 (M24) |
| Length availability (as marked, metric) | 2–120 mm matrix, every marked cell = to order (legend: black-triangle marker = to order): M1.6/M2 from 2–5 mm · M2.5 3 mm and 5 mm+ · M3–M5 from 3–60 mm · M6–M10 to 100 mm · M12–M16 to 120 mm · M20 to 100 mm · M24 to 100 mm; the whole line is a made-to-order schedule — quote lead time per pair |
| Length axis (imperial, unclaimed) | imperial matrix tabulates No.2-56–3/8-24 × 1/8″–2″, but its cell markers are not defined by the collected legend — imperial pairs at quotation |
| Standard materials | Steel, A2 stainless steel, A4 stainless steel; other materials and finishes on request |
Materials
- Steel (standard)
- A2 stainless steel (standard)
- A4 stainless steel (standard)
- Other materials and finishes on request
Ordering & documentation
Documents
Shipments of TX34 6-Lobe Pin TX Security Grub Screw — Cone Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for TX34 6-Lobe Pin TX Security Grub Screw — Cone Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (TX34 6-Lobe Pin TX Security Grub Screw — Cone Point), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for tx34 6-lobe pin tx security grub screw — cone point is 10,000 pieces (applies to the standard sizes and finishes for tx34 6-lobe pin tx security grub screw — cone point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for tx34 6-lobe pin tx security grub screw — cone point run 3–7 days. Quantities or variants of tx34 6-lobe pin tx security grub screw — cone point outside the standard range are confirmed at quotation.
Storage & shipping
TX34 6-Lobe Pin TX Security Grub Screw — Cone Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store tx34 6-lobe pin tx security grub screw — cone point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When is cone point the wrong choice?
Whenever the mating surface has to survive. The cone penetrates by design — that is where its class-leading torsional holding comes from — so it mars shafts, leaves a crater in soft materials, and is a one-position fixing: back it out and the dimple stays. Flat point (TX32) is the non-marring answer for adjusted joints and finished surfaces; cup point (TX28) is the middle path; dog point (TX33) when the part must rotate on the screw. Cone point earns its keep in permanent settings, as a pivot, or as an adjusting screw that is set once and locked.
How does the security drive change a permanent set screw?
It closes the usual back door. A conventional cone point set screw is defeated by any hex key that fits its socket; TX34’s 6-lobe pin socket requires the matched restricted insert bit, and the collected page adds the cam-out resistance that lets you torque it to full holding without rounding the recess. For permanent settings that is the combination that matters: maximum holding at the tip, and no casual tool in the world that will turn it back out.
What should an RFQ for TX34 state?
State the designation (TX34 6-lobe pin TX cone point grub screw), thread size and length, material (steel, A2 or A4 stainless as standard), the surface it will penetrate, quantity per size and lead time — the metric matrix marks every pair to order — plus TX-series bit supply. Imperial sizes are tabulated to 3/8-24 × 2″ but carry no legend-defined markers, so request confirmation per pair.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your TX34 6-Lobe Pin TX Security Grub Screw — Cone Point inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your TX34 6-Lobe Pin TX Security Grub Screw — Cone Point
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support