DIN 551 Slotted Grub Screws with Flat Point

DIN 551 grub (headless) set screws with slotted drive and flat point, M1 to M12 — the shallowest headless clamp that presses, not bites — with the full collected 10-size table: point diameter, slot and slot depth limits down to M1.

Last updated: 2026-11

Request a Quote

DIN 551 Slotted Grub Screws with Flat Point in an industrial setting
Illustrative image redrawn from real DIN 551 Slotted Grub Screws with Flat Point product references — not a photograph of stocked items.

Specifications

DIN 551 is the headless flat-point set screw: a fully threaded stub with a slot cut where the head would be, ending in a flat perpendicular point that presses squarely against the opposing surface. Because there is no head at all, the screw vanishes into the part — flush inside a collar, hub or latch — and the flat point spreads its clamp over the widest circle of any point form, leaving no more than a polished contact ring on the shaft. It is the choice where the mating surface must not be marked: stainless shafting, anodised parts, glass scales, adjustments that are re-made repeatedly. The collected table runs deeper than its dog- and cup-point siblings — down to M1 — and tabulates per size: the point diameter dp with max=nominal / min limits, the slot width n printed as Nominal with min/max limits, the slot depth t (min=nominal / max) and the pitch P. The slot is the only drive, so a correctly sized flat blade — matched to the n column — is what keeps the tiny M1–M2 slots from being chewed. Materials, property classes and finishes are not printed by the collected specification and follow the drawing callout.

Standard DIN 551 — slotted grub screws (headless set screws) with flat point
Series M1 – M12 (10 sizes tabulated; extends below the dog/cup point slotted series)
Tabulated geometry Per size: pitch P, point diameter dp (max=nominal / min), slot width n (Nominal / min / max), slot depth t (min=nominal / max)
Dimensions at M3 dp max=nominal 2 / min 1.75; n nominal 0.4 (max 0.6 / min 0.46); t min 0.8 / max 1.05
Dimensions at M6 dp max=nominal 4 / min 3.7; n nominal 1 (max 1.2 / min 1.06); t min 1.6 / max 2
Dimensions at M12 dp max=nominal 8.5 / min 8.14; n nominal 2 (max 2.31 / min 2.06); t min 2.8 / max 3.6
Point form Flat point — full-circle contact, presses without marking the mating surface
Materials / strength Not tabulated by the collected specification — per RFQ (property class and finish per drawing callout)
DIN 551 slotted grub screws with flat point — thread pitch, slot and flat-point diameter limits by thread sizeDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d thread sizePn minn maxt mint maxd1 max
M 10.250.260.40.40.520.5
M 1.20.250.260.40.40.520.6
M 1.40.30.260.40.480.630.7
M 1.60.350.310.450.560.740.8
M 20.40.310.450.640.841
M 2.50.450.460.60.720.951.5
M 30.50.460.60.81.052
M 3.50.60.560.70.961.212.2
M 40.70.660.81.121.422.5
M 50.80.8611.281.633.5
M 611.061.21.624
M 81.251.261.5122.55.5
M 101.51.661.912.437
M 121.752.062.312.83.68.5
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 551".
  • Source spanning row carried verbatim: "Publication date: 09 - 1986".
  • source grid ragged — 2/17 rows shorter than declared width 7; normalized with empty cells, carried verbatim (normalized with empty cells, carried verbatim; batch x152 acquisition)
DIN 551 slotted grub screws with flat point — approximate mass, kg per 1000 pcs, commercial lengthsDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
thread sizeM 1M1.2M 1.4M1.6M2M2.5M3M3,5M4M5M6M8M10M12
nominal length l
20.0070.0110.0150.021
2.50.0090.0140.0190.027
30.0110.0170.0230.0330.0480.0750.110.15
40.0150.0240.0310.0470.0670.110.150.210.260.4
50.40.0610.0680.140.20.270.340.520.72
60.0750.10.170.240.330.410.650.91.6
80.140.230.330.450.570.91.252.3
100.420.560.721.151.634.2
120.680.871.41.953.75.2
141.652.34.46.2
161.92.655.17.2
203.356.59.2
258.311.7
3014.2
  • Source spanning title row carried verbatim: "DIN 551 - 1986 - ≈ weigth, in kg x1000 pcs, (ρ=7,85 kg/dm 3 ) - commercial lengths".
  • source grid ragged — 1/17 rows shorter than declared width 15; normalized with empty cells, carried verbatim (normalized with empty cells, carried verbatim; batch x152 acquisition)

Materials

  • Material, property class and finish specified per RFQ — the collected specification table covers geometry only

Ordering & documentation

Documents

Shipments of DIN 551 Slotted Grub Screws with Flat Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 551 Slotted Grub Screws with Flat Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 551 Slotted Grub Screws with Flat Point), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 551 slotted grub screws with flat point is 10,000 pieces (applies to the standard sizes and finishes for din 551 slotted grub screws with flat point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 551 slotted grub screws with flat point run 3–7 days. Quantities or variants of din 551 slotted grub screws with flat point outside the standard range are confirmed at quotation.

Storage & shipping

DIN 551 Slotted Grub Screws with Flat Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 551 slotted grub screws with flat point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Flat point (DIN 551) or cup point (DIN 438) — both are slotted set screws, so when does the point form matter?

Compare the contact geometry: the flat point bears on its full point diameter — the dp column runs close to the thread minor, e.g. 4 mm nominal at M6 — so seating torque spreads over a wide circle and the shaft surface stays essentially unmarked. The cup point shrinks that contact to a narrow rim (dz 3 mm nominal at M6) and deliberately bites in for higher rotation resistance. So the rule of thumb: DIN 551 where the point re-seats often or the surface must survive — stainless shafting, adjusted settings, soft or finished parts; DIN 438 where the joint must never slip and a witness mark is acceptable. Both share the same slot limits n and t, so the driver tooling does not change between them.

What is the MOQ and lead time for these screws?

Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Common sizes in this designation are widely stocked — confirm the exact schedule against quantity and size mix at quotation.

What is the MOQ and lead time for DIN 551 Slotted Grub Screws with Flat Point?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 551 Slotted Grub Screws with Flat Point state?

State the full designation (DIN 551), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 551 Slotted Grub Screws with Flat Point inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your DIN 551 Slotted Grub Screws with Flat Point
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.