Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel)
Gypsum TEK self-drilling screws as printed by the collected special-purpose table: No. 6 at .035"–.090" and No. 12 / No. 14 at .089" min to .210" max, fastening gypsum board to metal studding — the heavier-framing counterpart of the Drywall TEK class.
Last updated: 2026-11
Specifications
The Gypsum TEK class covers the heavy end of board-to-steel fixing. The collected table splits it over two diameter groups: No. 6 screws with a .035"–.090" window, and No. 12 and No. 14 screws with a .089" min to .210" max window — roughly twice the metal of the Drywall TEK class — with the pairing printed as gypsum to metal studding, 2×4 or firring to steel. The two diameter groups let one line serve both the face-fixing screw and the heavier structural fixing that ties layered board through to heavier studs. As with the other special-purpose classes, the collected table prints no drill-point length; point geometry is confirmed against the framing system at quotation.
| Point class | Gypsum Teks — special-purpose class, label as printed by the collected table |
|---|---|
| Screw sizes (tabulated) | No. 6 · No. 12, No. 14 |
| Material window, No. 6 | .035" to .090" |
| Material window, No. 12 / No. 14 | .089" min to .210" max |
| Application pairing | Gypsum to metal studding; 2×4 or firring to steel — pairing printed by the collected table |
| Drill-point length | Not printed for this class — confirmed at quotation |
| Materials | Case-hardened carbon steel with corrosion-resistant plating is the standard construction for inch TEK self-drillers; stainless (410) and other finishes confirmed at quotation |
| Screw diameter | Recommended material thickness | Application pairing (as printed) |
|---|---|---|
| No. 6 | .035 to .090 | 2×4 or firring to steel |
| No. 12 | .089 min. to .210 max. | 2×4 or firring to steel |
| No. 14 | .089 min. to .210 max. | 2×4 or firring to steel |
Materials
- Case-hardened carbon steel with corrosion-resistant plating is the standard construction for inch TEK self-drillers; stainless (410) and other finishes confirmed at quotation
Ordering & documentation
Documents
Shipments of Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for gypsum tek self-drilling screws (heavy gypsum to steel) is 10,000 pieces (applies to the standard sizes and finishes for gypsum tek self-drilling screws (heavy gypsum to steel); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for gypsum tek self-drilling screws (heavy gypsum to steel) run 3–7 days. Quantities or variants of gypsum tek self-drilling screws (heavy gypsum to steel) outside the standard range are confirmed at quotation.
Storage & shipping
Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store gypsum tek self-drilling screws (heavy gypsum to steel) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Drywall TEK or Gypsum TEK for a board-to-steel job?
Measure the metal, not the board. The two classes share the application family, but their windows differ: the Drywall TEK class runs No. 6/No. 8 up to 26 gauge, while the Gypsum TEK class runs No. 6 at .035"–.090" and No. 12/No. 14 up to .210". A single 25-gauge stud with one board layer sits in either band at the light end; heavier studs, double layers or through-fixing to heavier steel behind the board push you into the No. 12/No. 14 windows. Because the printed windows overlap in the light range, the honest check is the measured metal thickness and the screw diameter your fixing pattern needs — bring both to the RFQ and the class is confirmed against the tables.
What is the MOQ and lead time for these self-drilling screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for these special-purpose TEK screws state?
State the point class (Stitch, Plymetal, Plymetal with Wings, Drywall or Gypsum TEK), the screw diameter from the class table, the base material it drills into and the total thickness or gauge of the stack, head form and drive, length, finish (for example zinc plated or 410 stainless), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your Gypsum TEK Self-Drilling Screws (Heavy Gypsum to Steel)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support