DIN 318 Wing Screws, Edged Wings (American Form)

DIN 318 wing screws with edged wings, American form, M4 to M12: wing span, grip and point geometry, the commercial length ladder to 60 mm, and a market-common reference table.

Last updated: 2026-11

Request a Quote

DIN 318 Wing Screws, Edged Wings (American Form) in an industrial setting
Illustrative image redrawn from real DIN 318 Wing Screws, Edged Wings (American Form) product references — not a photograph of stocked items.

Specifications

DIN 318 is the American-form wing screw — edged (flat-sided) wings you can turn hard with the heel of the hand — and the collected 07/1999-edition table runs M4 to M12 with the thread geometry (P, a max), the wing and body dimensions (e min, h min, g min), and the point-side dimensions d2 min / d3 min plus m min (3.2 at M4 to 10 at M12). The second grid is the commercial length ladder, 6 to 60 mm per size, where the M12 column prints an "X" at l 60 — the source's own marker, carried verbatim. A third table gives the market-common American-form geometry from M3, slightly freer than the DIN values, useful when a drawing calls the form rather than the standard. Hand-tightened fixtures, jigs, access covers and tooling plates are the duty: the screw is a clamp you operate without tools, not a structural fastener.

Standard / scope DIN 318 wing screws, edged wings, American form — M4 to M12, edition 07/1999
Thread geometry P and a max per size; point/body d2 min and d3 min; m min 3.2 (M4), 5 (M6), 8 (M10), 10 (M12)
Wing geometry e min, h min, g min per size — the span and grip that set the hand torque you can apply
Commercial lengths l 6 to 60 mm by size; the M12/l60 cell prints "X" (source order marker, verbatim)
Market reference American-form wing screws M3 to M12 market-common e/h/d2 values tabulated beside the DIN values
Not tabulated Material, strength, finish — per RFQ
DIN 318 wing screws (American form, edged wings) — 07/1999 edition, wing and head geometry by thread dDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d thread sizeM 4M 5M 6M 8M 10M 12
P0.70.811.251.51.75
a max2.12.4344.55.3
e min1924.529354763
h min91114172229
g min1.11.51.523.64.1
d2 min7911131821
d3 min5.57.5910.51417
m min3.2456.5810
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 318".
  • Edition row carried from the source grid: "Publication date: 07/1999".
DIN 318 1999 — commercial sizesDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
thread sizeM4M5M6M8M10M12
nominal length l
6X
8XXX
10XXXX
12XXXX
14XXXX
16XXXXXX
18XXXXXX
20XXXXXX
25XXXXX
30XXXXX
35XXXX
40XXXX
45XXX
50XXX
60X
  • Source spanning title row carried verbatim: "DIN 318 1999 - commercial sizes".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (7/1/2/4/5) — grid padded empty; per-row pre-pad widths: 7,7,1,2,4,5,5,5,7,7,7,7,7,7,7,7,7,7.
Wing screws (American form) — market-common geometry by thread dDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d thread sizeM 3M 4M 5M 6M 8M 10M 12
e18.5222226.830.335.347.5
h8.810.510.512.914.817.322.3
d27.89.59.511.913.515.320.5
  • Source spanning title row carried verbatim: "Dimensions in mm -wing nuts commonly used on the market".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (7/8) — grid padded empty; per-row pre-pad widths: 7,8,8,8,8.

Materials

  • Wing screws order in free-cutting steel, zinc-plated for shop use, or stainless A2 for washdown and outdoor tooling; plastic-winged equivalents are a different product family. State thread, length under the wing and finish on the RFQ — and if the screw must survive repeated high hand-torque, say so, because wing stiffness is where the cheap versions differ from the standard

Ordering & documentation

Documents

Shipments of DIN 318 Wing Screws, Edged Wings (American Form) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 318 Wing Screws, Edged Wings (American Form) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 318 Wing Screws, Edged Wings (American Form)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 318 wing screws, edged wings (american form) is 10,000 pieces (applies to the standard sizes and finishes for din 318 wing screws, edged wings (american form); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 318 wing screws, edged wings (american form) run 3–7 days. Quantities or variants of din 318 wing screws, edged wings (american form) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 318 Wing Screws, Edged Wings (American Form) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 318 wing screws, edged wings (american form) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

DIN 316 wing screws exist too — how does DIN 318 differ?

Both are American-form wing screws; the registered DIN 316 page carries the rounded-wing version, while DIN 318 tabulated here has the edged (flat-sided) wings. The edge is not cosmetic: a flat wing face transmits more torque from the same finger pressure and resists slipping under an oily thumb, which is why jigs and clamp straps usually print 318. The dimension columns are similar in shape but not identical in value, so the standards do not interchange on a controlled drawing — order by the number the drawing carries, and if you are designing new, pick by how the operator actually turns it.

Why does the length ladder print an "X" for M12 at 60 mm?

The "X" is the source table's own marker in the M12/60 cell — carried verbatim here, not cleaned up. Read pragmatically: it marks the corner of the commercial range where the M12 wing screw is not a stock length in the source's listing, not a dimension of zero. For an M12 that long the practical answer is usually a stud-and-wing-nut arrangement or a custom length, both of which we quote against drawing. For anything inside the printed ladder, name thread and length and the standard delivers the part.

What is the MOQ and lead time for DIN 318 Wing Screws, Edged Wings (American Form)?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 318 Wing Screws, Edged Wings (American Form) state?

State the full designation (DIN 318 Wing Screws, Edged Wings (American Form)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 318 Wing Screws, Edged Wings (American Form) inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your DIN 318 Wing Screws, Edged Wings (American Form)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.