DIN 96 Slotted Round Head Wood Screws
DIN 96 slotted round head wood screws from (1.6) to (8), with the full collected per-size table: domed head diameter and height with tolerance bands, slot width and depth, and thread diameter tolerances — the fully domed, no-countersink member of the classic wood-screw line for thin stock and through-fixing.
Last updated: 2026-11
Specifications
DIN 96 is the round-head wood screw: a full dome seated directly on the surface, needing no countersink at all. That makes it the wood screw for thin stock — the classic pattern on switch plates, small hardware brackets, toy and craft construction, and any joint too thin to cut a countersink into without weakening it. Because the head bears on the surface rather than inside the material, the whole clamping geometry differs from the countersunk line: the bearing ring under the dome spreads the load on the face fibres, and over-driving shows up immediately as a crushed face rather than a sunken head. The collected table runs (1.6) to (8) with, per size: head diameter d k nominal/max/min, head height k nominal/max/min — the only wood-screw table of this series that tabulates a height nominal band rather than a single max — slot width n and depth t, and thread diameter d s with tolerances. As with DIN 95, the collected table prints no length ranges, so lengths are confirmed per RFQ. Choose within the line by head: flush (DIN 97), crowned flush (DIN 95), or proud dome (this page); all three share the same coarse wood thread logic and pilot-hole discipline.
| Standard | DIN 96 — slotted round head wood screws |
|---|---|
| Series | (1.6), 2, 2.5, 3, 3.5, 4, 4.5, 5, (5.5), 6, (7), (8) — parenthesized sizes are non-preferred |
| Tabulated geometry | Per size: thread dia d s max/min, head dia d k nominal/max/min, head height k nominal/max/min, slot width n nominal/max/min, slot depth t max/min |
| Lengths | Not tabulated by the collected specification — lengths confirmed per RFQ |
| Materials / finish | Not tabulated by the collected specification — per RFQ (steel, brass, zinc-plated or stainless typical for the market) |
| Nominal thread | d s max (= nominal) (mm) | d s min (mm) | d k nominal (mm) | d k max (mm) | d k min (mm) | k nominal (mm) | k max (mm) | k min (mm) | n nominal (mm) | n max (mm) | n min (mm) | t max (mm) | t min (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| (1.6) | 1.6 | 1.2 | 3.2 | 3.58 | 2.83 | 1.1 | 1.3 | 0.9 | 0.4 | 0.6 | 0.46 | 0.7 | 0.55 |
| 2 | 2 | 1.6 | 4 | 4.38 | 3.62 | 1.4 | 1.6 | 1.2 | 0.5 | 0.7 | 0.56 | 0.9 | 0.7 |
| 2.5 | 2.5 | 2.1 | 5 | 5.38 | 4.62 | 1.7 | 1.9 | 1.5 | 0.6 | 0.8 | 0.66 | 1.1 | 0.85 |
| 3 | 3 | 2.6 | 6 | 6.38 | 5.62 | 2.1 | 2.3 | 1.9 | 0.8 | 1 | 0.86 | 1.35 | 1.05 |
| 3.5 | 3.5 | 3.02 | 7 | 7.45 | 6.55 | 2.4 | 2.6 | 2.1 | 0.8 | 1 | 0.86 | 1.6 | 1.2 |
| 4 | 4 | 3.52 | 8 | 8.45 | 7.55 | 2.8 | 3 | 2.6 | 1 | 1.2 | 1.06 | 1.8 | 1.4 |
| 4.5 | 4.5 | 4.02 | 9 | 9.45 | 8.55 | 3.1 | 3.34 | 2.86 | 1 | 1.2 | 1.06 | 2 | 1.55 |
| 5 | 5 | 4.52 | 10 | 10.45 | 9.55 | 3.5 | 3.74 | 3.26 | 1.2 | 1.51 | 1.26 | 2.3 | 1.75 |
| (5.5) | 5.5 | 5.02 | 11 | 11.55 | 10.45 | 3.8 | 4.04 | 3.56 | 1.2 | 1.51 | 1.26 | 2.5 | 1.9 |
| 6 | 6 | 5.52 | 12 | 12.55 | 11.45 | 4.2 | 4.44 | 3.96 | 1.6 | 1.91 | 1.66 | 2.7 | 2.1 |
| (7) | 7 | 6.42 | 14 | 14.55 | 13.45 | 4.9 | 5.14 | 4.66 | 2 | 2.31 | 2.06 | 3.2 | 2.45 |
| (8) | 8 | 7.42 | 16 | 16.55 | 15.45 | 5.6 | 5.84 | 5.36 | 2 | 2.31 | 2.06 | 3.6 | 2.8 |
Materials
- Material and finish specified per RFQ — the collected specification table covers geometry only
Ordering & documentation
Documents
Shipments of DIN 96 Slotted Round Head Wood Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 96 Slotted Round Head Wood Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 96 Slotted Round Head Wood Screws), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 96 slotted round head wood screws is 10,000 pieces (applies to the standard sizes and finishes for din 96 slotted round head wood screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 96 slotted round head wood screws run 3–7 days. Quantities or variants of din 96 slotted round head wood screws outside the standard range are confirmed at quotation.
Storage & shipping
DIN 96 Slotted Round Head Wood Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 96 slotted round head wood screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When is a round head the right wood screw head?
When the stock is too thin for a countersink, when the surface must not be cut, or when the dome is the desired finish. The head bears on the face of the material instead of inside a countersink, so no stock is removed at assembly — the tradeoff is that the head stands proud and the bearing load concentrates in a ring under the dome, which the table sizes through the d k and k rows per diameter.
What should an RFQ for DIN 96 wood screws state?
The designation, diameter and length (lengths are not tabulated in the collected specification, so confirm stock lengths at quotation), material and finish, and quantity per size. For visible work, state the head finish — domed heads show plating quality more than countersunk heads do. Head and slot tolerances are on this page; commercial terms follow the quotation.
What is the MOQ and lead time for these screws?
Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Common sizes in this designation are widely stocked — confirm the exact schedule against quantity and size mix at quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 96 Slotted Round Head Wood Screws inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 96 Slotted Round Head Wood Screws
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support