DIN 465 Knurled Thumb Screws

DIN 465 knurled thumb screws, M3–M6 with lengths 4–20 mm — the hand-tightened knurled-head screw with a slotted head face, carrying the collected head-geometry rows and the length×thread availability grid; the DIN 464 counterpart page covers its sibling.

Last updated: 2026-11

Request a Quote

DIN 465 Knurled Thumb Screws in an industrial setting
Illustrative image redrawn from real DIN 465 Knurled Thumb Screws product references — not a photograph of stocked items.

Specifications

The DIN 465 thumb screw is the hand-adjustment fastener: a knurled cylindrical head that fingers tighten, with a slot across the head face for a screwdriver when the adjustment has to be torqued or final-sealed. The collected source serves two pieces of data. The head geometry comes as four unnamed size columns carrying d2 = 12/16/20/24, head diameter d3 = 6/8/10/12, head height h = 7,5/9,5/11,5/15 and slot width n = 0,8/1/1,2/1,6 — the source does not label which of the four columns maps to which thread, and the values rise monotonically in the same order as the M3–M6 ladder (this mapping is flagged under the table; verify against the standard before quoting a head diameter for a specific thread). The availability grid keys length l = 4 to 20 mm against thread d1 = M3 to M6: every thread takes 10–20 mm, M3 additionally starts at 4 mm, M4 at 5 mm, M5 at 6 mm — the grid ends at 20 mm, so longer lengths are not established by this source. Where the drawing wants the low head form or a different head height, this catalog's DIN 464 and DIN 653 pages cover the sibling thumb screws. Knurl pattern, material and finish are not tabulated by the collected specification — per RFQ.

Standard DIN 465 — knurled thumb screws (knurled cylindrical head, slotted head face, hand-tight adjustment screw)
Thread range d1: M3 – M6 (four sizes in the collected grid)
Lengths l = 4 – 20 mm per the availability grid: M3 from 4 mm, M4 from 5 mm, M5 from 6 mm; all threads take 10–20 mm; longer lengths not established by this source — per RFQ
Head geometry Four size columns as printed: d2 12/16/20/24; head dia. d3 6/8/10/12; head height h 7,5/9,5/11,5/15; slot width n 0,8/1/1,2/1,6 — thread mapping unlabelled in the source (see table note)
Driving Fingers on the knurl for adjustment; slot width n 0,8–1,6 mm takes a screwdriver for final tightening
Materials / finishes / knurl pattern Not tabulated by the collected specification — per RFQ (state material, finish and knurl form at quotation)
DIN 465 knurled thumb screws — head geometry per size column and length×thread availability gridAll dimensions in millimetres, comma decimal separators preserved from the source. The source serves the head geometry as four unnamed size columns (printed in the order d2 = 12/16/20/24, d3 = 6/8/10/12, h = 7,5/9,5/11,5/15, n = 0,8/1/1,2/1,6) while the availability grid keys lengths to thread d1 = M3–M6; the mapping between the geometry columns and the thread ladder is not labelled by the source (see anomaly note). "+" in the grid = length/thread combination offered; empty = not offered. Knurl pattern, material and finish are not tabulated — per RFQ.
Size Column (as printed)d2d3hn
Column 11267,50,8
Column 21689,51
Column 3201011,51,2
Column 42412151,6
  • Row 1 (Column 1): The source does not label which thread (M3–M6) each of the four geometry columns belongs to; the columns are reproduced in printed order (d2/d3/h/n values rise monotonically, consistent with the M3→M6 ladder). Verify against the standard before quoting a head diameter for a specific thread.
DIN 465 knurled thumb screws — length×thread availability grid (l 4–20, M3–M6)"+" = offered by the source; empty cell = combination not offered in the capture. The length ladder ends at 20 in the capture; longer lengths are not established by this source — per RFQ.
Length (l)M3M4M5M6
4+
5++
6+++
8+++
10++++
12++++
16++++
20++++

Materials

  • Material and finish specified per RFQ — thumb screws live on adjustment points that get fingered constantly; state the environment and whether the slot is a torque requirement or a sealing feature with the order

Ordering & documentation

Documents

Shipments of DIN 465 Knurled Thumb Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 465 Knurled Thumb Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 465 Knurled Thumb Screws), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 465 knurled thumb screws is 10,000 pieces (applies to the standard sizes and finishes for din 465 knurled thumb screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 465 knurled thumb screws run 3–7 days. Quantities or variants of din 465 knurled thumb screws outside the standard range are confirmed at quotation.

Storage & shipping

DIN 465 Knurled Thumb Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 465 knurled thumb screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

What is the difference between DIN 465 and DIN 464 thumb screws, and what does the collected DIN 465 table establish?

The DIN 464 page in this catalog covers its sibling — the two standards share the knurled thumb-screw function and the M3–M6 working range, differing in the head form (464 is the high knurled head without the slotted face arrangement, 465 carries the slot n across the head face — check the two pages' head-geometry rows against your drawing rather than assuming). On what this source establishes for DIN 465: the availability grid is clean — lengths 4 to 20 mm against M3–M6, with each thread entering the ladder at a staggered minimum (M3 at 4 mm, M4 at 5 mm, M5 at 6 mm, M6 at 10 mm). The head geometry carries a caveat flagged under the table: the source prints four unnamed size columns (d2 12/16/20/24, d3 6/8/10/12, h 7,5/9,5/11,5/15, n 0,8/1/1,2/1,6) without labelling which column is which thread — the values rise in the same order as the M3→M6 ladder, which is consistent but not proof, so verify against the standard before quoting a head diameter for a specific thread. Knurl pattern, material and finish are not in the collected table at all — RFQ lines, as is anything beyond the 20 mm length limit the grid ends at.

What is the MOQ and lead time for DIN 465 Knurled Thumb Screws?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 465 Knurled Thumb Screws state?

State the full designation (DIN 465), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 465 Knurled Thumb Screws inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your DIN 465 Knurled Thumb Screws
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.