DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point
DIN 922 slotted pan head screws with small head and full dog point, M1,4-M10: thread pitch, small pan head dk/k, dog point dp/l2, slot n/t, undercut f and z, plus the available thread lengths l1 and pin lengths l2 per thread - the locating-screw identity for jig and fixture work.
Last updated: 2026-11
Specifications
DIN 922 looks like a small pan head slotted screw until you reach the shank end: a full dog point (dp wide, l2 long) sticks out under the thread, and the screw registers itself in a counterbore or locating hole while the clamp goes down — the classic jig, fixture and gauge-building identity. The collected ladder runs eleven threads M1,4 to M10 in two blocks. The head stays deliberately small — dk max runs 2 mm at M1,4 up to 13 mm at M10, with k only 0,9 to 4,6 mm nominal — so it clears adjacent clamps in dense tooling. The dog point dp runs just under the thread minor (0,8 at M1,4 up to 7,5 at M10) with l2 from 0,6 to 10 mm, and the thread stops short with an undercut f and a transition z, both printed per size. Lengths are orderable straight off the two availability matrices: thread length l1 from 1,6 to 20 mm and pin length l2 from 0,6 to 10 mm, with the "+" grid showing which thread each length serves. Materials per the collected sheet: steel 5.8, stainless A1, brass. Where the application is jig and fixture work on small threads and the screw must locate before it clamps, this is the identity; the plain cheese head without a point is DIN 84, already in the catalog.
| Series / scope | DIN 922 slotted pan head screws with small head and full dog point, threads M1,4 to M10 in two collected blocks (M1,4-M3 and M 3,5-M10), 11 sizes — head, point, slot and undercut geometry with l1/l2 availability matrices |
|---|---|
| Head geometry dk / k | dk max = nominal 2 to 13 mm (min. 1,86 to 12,73); k nominal 0,9 to 4,6 mm — a deliberately small pan head for dense tooling layouts |
| Dog point dp / l2 | dp max = nominal 0,8 to 7,5 mm (min. 0,775 to 7,464) — just under the thread minor; available pin lengths l2 0,6 to 10 mm per the matrices |
| Slot n / depth t | n nominal 0,25 to 1,6 mm (min./max. as printed); t min. 0,45 to 2,3 mm, max. 0,6 to 2,8 mm |
| Undercut f / transition z | f approx. 0,25 to 1,1 mm; z approx. 0,2 to 1 mm — carried per the source's approx. qualifiers, no legend entries for f or z |
| Available thread lengths l1 | 1,6 to 20 mm; block-1 (M1,4-M3) prints tolerance "js 15 for l1 and l2" while block-2 and both l2 blocks print min./max. bands — carried as printed |
| Materials / thread class | Steel 5.8, Stainless A1, Non Ferrous Brass, Plastic "-"; thread print "for size M1,4 - 6h, from size M1,6 - 6g" |
| Not tabulated | Surface finishes, strength beyond the 5.8 steel print, drive variants (no recess option tabulated) — per RFQ |
| Thread size d | M1,4 | M1,6 | M2 | M2,5 | M3 |
|---|---|---|---|---|---|
| P | 0,3 | 0,35 | 0,4 | 0,45 | 0,5 |
| dk (max = nominal size) | 2 | 2,3 | 2,8 | 3,5 | 4 |
| dk (min.) | 1,86 | 2,16 | 2,66 | 3,32 | 3,82 |
| dp (max = nominal size) | 0,8 | 0,8 | 1,2 | 1,5 | 2 |
| dp (min.) | 0,775 | 0,775 | 1,175 | 1,475 | 1,975 |
| f (approx.) | 0,25 | 0,25 | 0,3 | 0,4 | 0,45 |
| k (Nominal size) | 0,9 | 1 | 1,2 | 1,5 | 1,8 |
| k (max.) | 1,02 | 112 | 1,32 | 1,62 | 0,92 |
| k (min.) | 0,78 | 0,88 | 1,08 | 1,38 | 1,68 |
| n (Nominal size) | 0,25 | 0,3 | 0,3 | 0,4 | 0,5 |
| n (min.) | 0,31 | 0,36 | 0,36 | 0,46 | 0,56 |
| n (max) | 0,45 | 0,5 | 0,5 | 0,6 | 0,7 |
| r (max.) | 0,1 | 0,1 | 0,1 | 0,1 | 0,1 |
| t (min.) | 0,45 | 0,5 | 0,75 | 0,75 | 0,9 |
| t (max.) | 0,6 | 0,7 | 0,95 | 0,95 | 1,15 |
| z (approx.) | 0,2 | 0,2 | 0,35 | 0,35 | 0,4 |
- Row 8 (k (max.)): Row k (max.) prints "112" at M1,6 and "0,92" at M3 — against the block's own k nominal 1 / 1,8, k min. 0,88 / 1,68 and neighbours 1,32 / 1,62 these are the source's own cells; transcribed as printed, not normalized; verify against the standard before engineering use.
- The source legend explains d, k, dp, n, t, dk, l2, l1 and a; P, f and z have no legend entry and "a - length undercut" has no column in either block - labels are the source header words verbatim.
- Makings print Steel 5.8, Stainless A1, Non Ferrous Brass, Plastic "-", thread "for size M1,4 - 6h, from size M1,6 - 6g".
| l1 Nominal size | Tolerance | M1,4 | M1,6 | M2 | M2,5 | M3 |
|---|---|---|---|---|---|---|
| 1,6 | js 15 for l1 and l2 | + | + | + | ||
| 2 | js 15 for l1 and l2 | + | + | + | + | |
| 2,5 | js 15 for l1 and l2 | + | + | + | + | + |
| 3 | js 15 for l1 and l2 | + | + | + | + | |
| 4 | js 15 for l1 and l2 | + | + | + | ||
| 5 | js 15 for l1 and l2 | + | + | |||
| 6 | js 15 for l1 and l2 | + |
- Block-1 l1 prints a Tolerance column ("js 15 for l1 and l2") where block-2 l1 and both l2 blocks print min./max. columns - structural inconsistency carried as printed.
| l2 Nominal size | min. | max. | M1,4 | M1,6 | M2 | M2,5 | M3 |
|---|---|---|---|---|---|---|---|
| 0,6 | 0,6 | 0,85 | + | ||||
| 0,8 | 0,8 | 1,05 | + | + | |||
| 1 | 1 | 1,25 | + | + | + | ||
| 1,2 | 1,2 | 1,45 | + | + | + | + | |
| 1,6 | 1,6 | 1,85 | + | + | + | + | |
| 2 | 2 | 2,25 | + | + | + | ||
| 2,5 | 2,5 | 2,75 | + | + | |||
| 3 | 3 | 3,25 | + |
| Thread size d | M 3,5 | M4 | M5 | M6 | M8 | M10 |
|---|---|---|---|---|---|---|
| P | 0,6 | 0,7 | 0,8 | 1 | 1,25 | 1,5 |
| dk (max.= nominal size) | 4,5 | 5,5 | 6,5 | 8 | 10 | 13 |
| dk (min.) | 4,32 | 5,32 | 6,28 | 7,78 | 9,78 | 12,73 |
| dp (max.=nominal size) | 2,5 | 2,8 | 3,5 | 4,5 | 6 | 7,5 |
| dp (min.) | 2,475 | 2,775 | 3,47 | 4,47 | 5,97 | 7,464 |
| f (approx.) | 0,5 | 0,6 | 0,7 | 0,8 | 0,9 | 1,1 |
| k (nominal size) | 2 | 2,4 | 2,7 | 3,1 | 3,8 | 4,6 |
| k (max.) | 2,12 | 2,52 | 2,82 | 3,25 | 3,95 | 4,75 |
| k (min.) | 1,88 | 2,28 | 2,58 | 2,95 | 3,65 | 4,45 |
| n (nominal size) | 0,5 | 0,6 | 0,8 | 1 | 1,2 | 1,6 |
| n (min.) | 0,56 | 0,66 | 0,86 | 1,06 | 1,26 | 1,66 |
| n (max.) | 0,7 | 0,8 | 1 | 1,2 | 1,51 | 1,91 |
| r (max.) | 0,1 | 0,2 | 0,2 | 0,25 | 0,4 | 0,4 |
| t (min.) | 1 | 1,2 | 1,3 | 1,5 | 1,9 | 2,3 |
| t (max.) | 1,3 | 1,5 | 1,6 | 1,9 | 2,4 | 2,8 |
| z (approx.) | 0,45 | 0,5 | 0,6 | 0,7 | 1 | 1 |
- Thread header prints "M 3,5" (space) against block-1's "M1,4"-style tokens - source spelling carried.
| l1 Nominal size | min. | max. | M 3,5 | M4 | M5 | M6 | M8 | M10 |
|---|---|---|---|---|---|---|---|---|
| 2,5 | 2,4 | 2,6 | + | |||||
| 3 | 2,9 | 3,1 | + | + | ||||
| 4 | 3,8 | 4,2 | + | + | + | |||
| 5 | 4,8 | 5,2 | + | + | + | + | ||
| 6 | 5,8 | 6,2 | + | + | + | + | + | |
| 8 | 7,8 | 8,2 | + | + | + | + | + | |
| 10 | 9,8 | 10,2 | + | + | + | + | ||
| 12 | 11,7 | 12,3 | + | + | + | |||
| 16 | 15,7 | 16,3 | + | + | ||||
| 20 | 19,6 | 20,4 | + |
| l2 Nominal size | min. | max. | M 3,5 | M4 | M5 | M6 | M8 | M10 |
|---|---|---|---|---|---|---|---|---|
| 1,6 | 1,6 | 1,85 | + | |||||
| 2 | 2 | 2,25 | + | + | ||||
| 2,5 | 2,5 | 2,75 | + | + | + | |||
| 3 | 3 | 3,25 | + | + | + | + | ||
| 4 | 4 | 4,3 | + | + | + | + | ||
| 5 | 5 | 5,3 | + | + | + | + | ||
| 6 | 6 | 6,3 | + | + | + | |||
| 8 | 8 | 8,36 | + | + | ||||
| 10 | 10 | 10,36 | + |
Materials
- The collected sheet lists steel 5.8 (the standard jig-building class), stainless A1 and brass for the non-ferrous lane; plastic prints "-". A 5.8 dog-point screw is sized for location and light clamping, not structural preload — where the fixture sees torque or vibration, state the strength class explicitly on the RFQ. Brass versions serve electrical and spark-safe tooling; A1 stainless handles washdown and corrosion exposure. The dog point runs hard against its locating bore — confirm the counterbore diameter and the point entry chamfer on your detail drawing before ordering.
Ordering & documentation
Documents
Shipments of DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 922 slotted pan head screws with small head and full dog point is 10,000 pieces (applies to the standard sizes and finishes for din 922 slotted pan head screws with small head and full dog point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 922 slotted pan head screws with small head and full dog point run 3–7 days. Quantities or variants of din 922 slotted pan head screws with small head and full dog point outside the standard range are confirmed at quotation.
Storage & shipping
DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 922 slotted pan head screws with small head and full dog point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When does DIN 922 replace a plain slotted cheese head DIN 84 — and when not?
The dog point is the difference. A DIN 84 screw clamps wherever its thread ends; a DIN 922 screw drops its dp x l2 point into a counterbore first, so the part locates repeatably before the slot takes torque — which is why jig, fixture, gauge and switchgear builders specify DIN 922 for locating stations. If your assembly has no locating bore and cost matters, the plain cheese head is the right identity. Note the head is deliberately smaller than a standard pan head (dk 13 mm even at M10), so it sits where full-size heads would foul neighbouring clamps — check the bearing area if you clamp hard through it.
The small-size block prints odd k (max.) values ("112" at M1,6, "0,92" at M3) — what do I order against?
Read them as printed but do not build with them. In context the block's own numbers show the problem: k nominal is 1 and 1,8 mm, k min. 0,88 and 1,68, and the neighbouring maxima print 1,32 and 1,62 — so "112" reads like a dropped decimal comma (1,12) and "0,92" like a lost leading "1" (1,92). The collected page flags nothing, and this page transcribes verbatim and flags rather than correcting. For ordering it does not matter: you order by designation, thread and length (l1/l2 from the availability matrices), not by head maximum. For machining a recess or a gauge that must clear the head, verify k against the standard or a second source first.
What should an RFQ for DIN 922 dog-point screws state?
State the designation (DIN 922), thread size and pitch, thread length l1 and pin length l2 (pick both from the availability matrices — not every length serves every thread), material (steel 5.8, stainless A1 or brass), finish if not plain, and quantity per size. If the screw locates into a machined counterbore, add the counterbore diameter so the supplier confirms the dog point dp/l2 fit. Commercial terms are confirmed at quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 922 Slotted Pan Head Screws with Small Head and Full Dog Point
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support