DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws

DIN 7997 cross recessed countersunk flat head wood screws, No. 2 to No. 8: shank and head geometry, type H/Z recess depths and the commercial length ladder to 80 mm.

Last updated: 2026-11

Request a Quote

DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws in an industrial setting
Illustrative image redrawn from real DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws product references — not a photograph of stocked items.

Specifications

DIN 7997 is the flat countersunk wood screw with cross recess — the flush-finish timber screw, the default where hardware must sit at or below the wood surface (hinges, slide rails, floor plates, any face another part rides over). The collected 12/2016-edition table runs sizes 2 to 8 with shank ds min, countersunk head diameter dk nom, head height k max., the cross recess number and the m depth columns for type H (Phillips) and type Z (Pozi, as the source labels it) drivers (type Z 2.8 at size 2.5 to 6.1 at size 8), and the commercial length ladder 10 to 80 mm with its mass table; the superseded 12/2010 edition is transcribed as a separate table alongside, both verbatim. The flush result depends on the 90° seat: drill-and-csk tooling matched to dk/k per size is part of the joint, not an option.

Standard / scope DIN 7997 cross recessed countersunk flat head wood screws — sizes 2 to 8, edition 12/2016 (supersedes 12/2010; the superseded edition is transcribed as a separate table)
Shank / head ds min per size; countersunk head dk nom; head height k max. — the seat depth the 90° csk must produce
Cross recess Recess number per size; m depths for type H and type Z drivers (Z 2.8 at size 2.5 → 6.1 at size 8)
Commercial lengths l Ladder 10 to 80 mm; approximate mass per 1000 pcs (ρ=7,85 kg/dm³) tabulated per size/length
Not tabulated Point type, material, finish — per RFQ
DIN 7997 cross recessed countersunk flat head wood screws — 12/2016 edition, head geometry by thread sizeDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
thread size22.53.03.54.04.55.05.56.078
ds min1.62.12.63.023.524.024.525.025.526.427.42
dk nom3.84.75.66.57.58.39.210.21112.514
k max.1.21.51.651.932.22.352.52.7533.54
Cross recess nr01122223334
m (type H)-2.72.93.94.44.64.86.26.66.88.7
m (Type Z)-2.8344.24.456.16.378.5
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 7997 Publication date: 12/2016 Supersedes DIN 7997: 12/2010".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (11/12) — grid padded empty; per-row pre-pad widths: 11,12,12,12,12,12,12,12.
DIN 7997 — superseded 12/2010 edition, head geometry by thread sizeDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
thread size22.53.03.54.04.55.05.56.078
ds min1.62.12.63.023.524.024.525.025.526.427.42
dk nom3.84.75.66.57.58.39.210.21112.514
k max.1.21.51.651.932.22.352.52.7533.54
Cross recess nr01122223334
m (type H)-2.72.93.94.44.64.86.26.66.88.7
m (Type Z)-2.8344.24.456.16.378.5
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 7997 Publication date: 12/2010 Supersedes DIN 7997: 12/1984".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (11/12) — grid padded empty; per-row pre-pad widths: 11,12,12,12,12,12,12,12.
DIN 7997 — approximate mass, kg per 1000 pcs (ρ=7,85 kg/dm³), commercial lengthsDimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d thread size22.533.544.555.5678
nominal length l
100.370.60.79
120.430.70.911.18
160.550.881.171.491.852.31
200.671.061.431.792.222.784.12
251.31.732.172.713.374.96
301.542.042.553.1945.8
351.772.352.943.684.556.63
402.012.663.224.175.147.46
452.983.664.655.738.29
504.055.146.329.12
604.816.117.5410.8
708.7212.5
809.914.3
  • Source spanning title row carried verbatim: "DIN 7997 - ≈ weigth in kg x1000 pcs, (ρ=7,85 kg/dm 3 ) - commercial items".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (12/1/5/6/8/10) — grid padded empty; per-row pre-pad widths: 12,12,1,5,6,8,10,10,10,10,10,10,10,10,10,10.

Materials

  • Zinc-plated steel interior, A2/A4 stainless or coated exterior, brass for visible furniture work — and where the screw heads stay exposed to handling, stainless also removes the rust-bleed that telegraphs through finished timber. State timber/board type for point selection, and H vs Z recess tooling per the m columns; hinges and hardware pre-drilled for one system should not be mixed with the other

Ordering & documentation

Documents

Shipments of DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 7997 cross recessed countersunk flat head wood screws is 10,000 pieces (applies to the standard sizes and finishes for din 7997 cross recessed countersunk flat head wood screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 7997 cross recessed countersunk flat head wood screws run 3–7 days. Quantities or variants of din 7997 cross recessed countersunk flat head wood screws outside the standard range are confirmed at quotation.

Storage & shipping

DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 7997 cross recessed countersunk flat head wood screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Flat (DIN 7997) or raised (DIN 7995) countersunk — same screw otherwise?

Same shank, same lengths, different head: DIN 7997 finishes flat with the wood, DIN 7995 leaves its dome above the surface. The choice is surface function — anything that rides over the joint (hinge leaf, slide, plate) wants the flat head, because a dome lifts the mating part and the joint rattles; decorative or wear-shedding exposed screws take the raised. Both need their matching csk geometry, and the k columns differ (k max. flat versus the raised head height), so the countersink tooling is not shared. On a drawing that just says "CSK wood screw", read the mating hardware: if a part sits on the head, it is DIN 7997.

Why is the recess labeled both type H and type Z?

The two columns are the depth data for the two cross-recess systems — type H (Phillips) and type Z (the source's label for the Pozi-type geometry) — printed per size (type Z 4.2 at size 4, for example). One recess, two tool systems with different engagement: the deeper-engaging Z/Pozi driver cambs out less under high torque, which is why production wood assembly standardized on it, while H remains in consumer and legacy tooling. The failure mode of mixing systems is recess destruction and a screw you cannot back out of finished work — so fix the tool system per line. Volume orders can be supplied with recess inspection against the m band your assembly is tooled to.

What is the MOQ and lead time for DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws state?

State the full designation (DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your DIN 7997 Cross Recessed Countersunk Flat Head Wood Screws
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.