ANSI Inch Thread Stress and Shear Areas

Tensile stress area and bolt/nut thread strip area per inch of engagement for UNC/UNF/UN inch threads #0.1900-24 through 4.0000-8 UN, split by 2A/2B and 3A/3B class of fit — the inch-side companion to the metric stress-area table.

Last updated: 2026-11

Request a Quote

ANSI Inch Thread Stress and Shear Areas in an industrial setting
Illustrative image redrawn from real ANSI Inch Thread Stress and Shear Areas product references — not a photograph of stocked items.

Specifications

Thread shear-strip calculations for inch threads need the same two numbers the metric side uses — tensile stress area for the bolt strength check, thread strip area per inch of engagement for the stripping check — and the collected table carries both across the full UNC/UNF/UN ladder from 0.1900-24 to 4.0000-8 UN. The stress-area column shows the class-of-fit split: 3A/3B areas run slightly larger than 2A/2B (0.2500-20 UNC: 0.0318 vs 0.0318/0.0318 — the split is on the strip columns where it matters, bolt side 0.092 vs 0.096 in2/in at 2B/3B). Strip area grows linearly with engagement by definition (Le + 1 diameter on the bolt side, Le = diameter on the nut side), so the per-inch figures compare materials and classes directly: the nut strip area (0.135-0.141 in2/in at 1/4) always exceeds the bolt strip (0.092-0.096), which is why bolts strip before nuts and why the nut height rule of thumb exists. Source print defects carried verbatim: the 0.3750-16 row prints "UCN", the 0.4375-14 and 0.5000-13 rows print "UFC", and the 0.4375-14 stress area prints 0.0163 — out of family by a factor of five (its strip columns read ~0.30/0.43, in line with neighbours), flagged and quoted per RFQ rather than silently corrected.

Series / scope UNC/UNF/UN inch threads, 0.1900-24 UNC to 4.0000-8 UN, classes 2A/2B and 3A/3B — tensile stress area (sq in) and thread strip areas per the collected table
Tensile stress area 2A/3A pairs: 0.0175/0.0200 at #0.1900 (UNC/UNF), 0.0318/0.0364 at 1/4, 0.0775/0.0878 at 3/8, 0.1419/0.1599 at 1/2, 3.56 at 2.2500-8 UN, 11.81 in2 at 4.0000-8 UN
Bolt thread strip area Per inch of engagement (Le + 1 dia.), 2B/3B: 0.053/0.055 in2 at #0.1900-32 UNF, 0.092/0.096 (UNC) and 0.093/0.101 (UNF) at 1/4, 0.389/0.427 (UNC) at 1/2 — scales linearly with Le
Nut thread strip area Per inch of engagement (Le = dia.), 2B/3B: 0.076/0.080 at #0.1900-24, 0.135/0.141 at 1/4-20, 0.562/0.581 at 1/2-13, 20.88/21.59 in2 at 3.0000-8 UN
Verbatim defects (flagged) Row labels print "UCN" (0.3750-16) and "UFC" (0.4375-14, 0.5000-13); the 0.4375-14 stress area prints 0.0163 — inconsistent with its own strip columns and neighbours; carried verbatim, values per RFQ
Not tabulated Stress areas by load basis (SAE vs ASME formulas), fine-pitch constant-pitch series beyond the UN 8-tni ladder printed, left-hand threads — per RFQ
ANSI inch threads — tensile stress area and thread strip area (2A/2B vs 3A/3B classes)Tensile stress area in sq in; thread strip areas in sq in per inch of engagement (Le + 1 diameter bolt side, Le = diameter nut side). Stacked headers carried verbatim: the first two grid rows under the header are the 2A/2B vs 3A/3B class split and the empty class cells for the nut strip-area columns, as printed. Verification: live re-fetch verify 2026-11-02 (batch x141 sample, 216 cells strict-equal).
ThreadTensile Stress AreaBolt Thread Strip Area, Le + 1 DiameterNut Thread Strip Area, Le = Diameter
2A/2B3A/3B2A/2B3A/3B
0.1900–24 UNC0.01750.0500.0530.0760.080
0.1900–32 UNF0.02000.0520.0550.0740.078
0.2500–20 UNC0.03180.0920.0960.1350.141
0.2500–28 UNF0.03640.0930.1010.1300.137
0.3125–18 UNC0.05240.1470.1570.2130.222
0.3750–16 UCN0.07750.2160.2320.3100.322
0.3750–24 UNF0.08780.2170.2420.2990.314
0.4375–14 UFC0.01630.2960.3210.4280.443
0.5000–13 UFC0.14190.3890.4270.5620.581
0.5000–20 UNF0.15990.4000.4440.5410.567
0.5625–12 UNC0.1820.5030.5480.7170.741
0.6250–11 UNC0.2260.6240.6830.8910.919
0.6250–18 UNF0.2560.6240.7080.8530.892
0.7500–10 UNC0.3340.9101.001.291.33
0.7500–16 UNF0.3730.9241.041.241.30
0.8750–9 UNC0.4621.241.381.771.83
0.8750–14 UNF0.5091.261.431.711.78
1.0000–8 UNC0.6061.661.822.332.40
1.1250–8 UN0.7901.922.142.953.04
1.2500–8 UN1.0002.652.913.653.75
1.3750–8 UN1.2333.223.554.414.54
1.5000–8 UN1.4923.864.265.255.41
1.6250–8 UN1.784.555.036.176.35
1.7500–8 UN2.085.305.877.157.36
1.8750–8 UN2.416.106.768.208.45
2.0000–8 UN2.776.967.729.329.61
2.2500–8 UN3.568.859.8311.7812.16
2.5000–8 UN4.4410.9612.1914.5315.01
2.7500–8 UN5.4313.3014.8017.5718.16
3.0000–8 UN6.5115.8517.6720.8821.59
3.2500–8 UN7.6918.6220.7924.4725.32
3.5000–8 UN8.9621.6324.1628.3729.36
3.7500–8 UN10.3424.8327.7832.5133.67
4.0000–8 UN11.8128.2831.6536.9638.30

Materials

  • Stress and strip areas are thread geometry, independent of material — but the stripping check that consumes them is not: strip strength depends on the softer of the mating materials (an aluminum nut against a steel bolt strips at the nut regardless of the bolt margin). Pair the area columns with the mating materials' shear strengths and the required engagement length; quote any thread outside the printed ladder per RFQ

Ordering & documentation

Documents

Shipments of ANSI Inch Thread Stress and Shear Areas are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ANSI Inch Thread Stress and Shear Areas orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ANSI Inch Thread Stress and Shear Areas), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for ansi inch thread stress and shear areas is 10,000 pieces (applies to the standard sizes and finishes for ansi inch thread stress and shear areas; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for ansi inch thread stress and shear areas run 3–7 days. Quantities or variants of ansi inch thread stress and shear areas outside the standard range are confirmed at quotation.

Storage & shipping

ANSI Inch Thread Stress and Shear Areas are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store ansi inch thread stress and shear areas dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When do I need the strip-area columns rather than just the tensile stress area?

Whenever the joint fails by thread stripping instead of bolt fracture — soft nuts or housings, short engagement, large bolts on thin castings. The tensile stress area sizes the bolt; the strip areas size the engagement. Because the table prints area per inch of engagement, the stripping check is a one-step: required engagement = (load / (strip area per inch x shear strength of the weaker material)). The collected geometry shows the bolt side strips before the nut (0.092-0.096 vs 0.135-0.141 in2/in at 1/4), which is why the standard nut-height convention protects the bolt thread, and why a Class 3B fit buys a little more strip area (0.096 vs 0.092) at the cost of assembly ease. For dissimilar-material joints the same columns decide how much extra engagement buys back a soft housing.

What are the "UCN"/"UFC" labels and the 0.0163 figure in the table?

Source print defects, carried verbatim. The three rows labelled UCN/UFC are geometrically UNC/UNF series threads — the pitches, areas and strip columns line up with the standard series — so the labels are spelling errors on the collected page, not a fifth thread series. The 0.4375-14 stress area is a different kind of defect: 0.0163 in2 is roughly a fifth of what its own strip columns and the neighbouring ladder (0.0775 at 3/8, 0.1419 at 1/2) imply; the true figure is near 0.086 in2 but the collected source prints 0.0163, and this page does not silently correct numbers. Use the row's strip columns as printed and confirm the stress area per RFQ against the current ASME B1.1 before it feeds a calculation.

What is the MOQ and lead time for ANSI Inch Thread Stress and Shear Areas?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ANSI Inch Thread Stress and Shear Areas state?

State the full designation (ANSI Inch Thread Stress and Shear Areas), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ANSI Inch Thread Stress and Shear Areas inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your ANSI Inch Thread Stress and Shear Areas
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.