Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series

Hex key and hex bit dimensions in inch series per ASME B18.3 — width across flats with tolerances from 0.028 to 3 in, across-corners limits, bit section dimensions in short and long series, bend radius, bit length and chamfer, transcribed row-for-row from the live-collected chart.

Last updated: 2026-11

Request a Quote

Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series in an industrial setting
Illustrative image redrawn from real Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series product references — not a photograph of stocked items.

Specifications

Every socket head cap screw and hex socket set screw in the inch world is driven by one of these keys — and a worn or undersize key rounds the socket before the fastener is tight, so the dimension table is as much a quality-control document as a tooling catalog. The collected chart runs the full ASME B18.3 inch ladder: nominal across-flats sizes from 0.028 in (before 1/16) through every fraction — 1/16, 5/64, 3/32, 1/8, 3/16, 1/4, 5/16, 3/8, 1/2, 3/4, 1 in — up to 3 in, each row carrying the width across flats with max/min tolerances (1/4 in key: 0.2500/0.2485), the width across corners limits (0.2845/0.2815 for the same key), the bit-section dimension pair (B) in max/min, the short-series and long-series dimension pairs (C), the minimum bend radius, the bit length and the maximum chamfer. The short/long series split matters for accessibility: a long-series key reaches a socket recessed below a shoulder or inside a housing, at the cost of tip alignment torque. From 1 1/4 in upward the source prints no long-series bit pair and gives the bit length directly (flagged on the table). Reading the table against a worn key: any measured across-flats below the printed minimum is a rounding hazard for the screw socket — retire the key before it wrecks the fastener. Matching key to screw: the key size follows the socket size called out by the screw standard (ASME B18.3 for socket head cap screws), not the screw diameter — though on this ladder they track closely. Tool steel grade, hardness and finish of keys and bits are not tabulated — per RFQ.

Standard ASME B18.3 — dimensions of hexagon keys and bits, inch series; nominal across-flats sizes 0.028 to 3 in, 29 tabulated rows
Width across flats (W) Per row: nominal decimal, max, min — examples: 1/16 in → 0.0625/0.0615; 1/4 in → 0.2500/0.2485; 1/2 in → 0.5000/0.4975; 1 in → 1.0000/0.9970
Width across corners (Y) Max/min per row — the diagonal measure that wears first; example 1/4 in: 0.2845/0.2815 in
Bit dimensions (B, C, R, L, K) B max/min (bit section pair), C short-series and long-series max/min pairs, R minimum bend radius, L length of bit, K maximum chamfer — long-series pair not tabulated from 1 1/4 in up (source prints "-" "-", gives L)
Tool steel / hardness / finish Not tabulated by the collected chart — per RFQ (state key or bit form, series and hardness requirement)
Hex key and bit dimensions — inch series per ASME B18.3 (0.028 to 3 in across flats), short and long seriesAll dimensions in inch, transcribed from a live DOM capture of the source table (rowspan-expanded grid). W = hexagon width across flats (nominal decimal, max, min); Y = width across corners (max, min); B and C are the printed key/bit cross-section and bend-dimension pairs — B max/min, C short-series max/min and long-series max/min (the source's symbols line defines W, Y, R and K but omits B and C — reproduced as printed); R = minimum radius of bend; L = length of bit; K = maximum chamfer. The source prints "-" for the nominal key designation on the three sub-1/16 sizes and "-" in the L column where no bit length is tabulated; long-series C runs only up to the 1 in key (larger sizes print "-" "-" and carry L instead).
Nom. Key / Bit & Socket SizeW Nominal (dec. in)W Max (in)W Min (in)Y Max (in)Y Min (in)B Max (in)B Min (in)C Short Series Max (in)C Short Series Min (in)C Long Series Max (in)C Long Series Min (in)R Min. Radius of Bend (in)L Length of Bit (in)K Max. Chamfer (in)
-0.0280.02800.02750.03140.03000.3120.1251.3121.1252.6882.5000.062-0.003
-0.0350.03500.03450.03930.03780.4380.2501.3121.1252.7662.5780.062-0.004
-0.0500.05000.04900.05600.05400.6250.4381.7501.5622.9382.7500.062-0.006
1/160.0620.06250.06150.07010.06800.6560.4691.8441.6563.0942.9060.062-0.008
5/640.0780.07810.07710.08800.08590.7030.5161.9691.7813.2813.0940.078-0.008
3/320.0940.09370.09270.10580.10350.7500.5622.0941.9063.4693.2810.094-0.009
7/640.1090.10940.10790.12380.12100.7970.6092.2192.0313.6563.4690.109-0.014
1/80.1250.12500.12350.14180.13900.8440.6562.3442.1563.8443.6560.125-0.015
9/640.1410.14060.13910.15930.15660.8910.7032.4692.2814.0313.8440.141-0.016
5/320.1560.15620.15470.17740.17450.9380.7502.5942.4064.2194.0310.156-0.016
3/160.1880.18750.18600.21350.21051.0310.8442.8442.6564.5944.4060.188-0.022
7/320.2190.21870.21720.24900.24601.1250.9383.0942.9064.9694.7810.219-0.024
1/40.2500.25000.24850.28450.28151.2191.0313.3443.1565.3445.1560.250-0.030
5/160.3120.31250.31100.35700.35311.3441.1563.8443.6566.0945.9060.312-0.032
3/80.3750.37500.37350.42850.42381.4691.2814.3444.1566.8446.6560.375-0.044
7/160.4380.43750.43550.50050.49441.5941.4064.8444.6567.5947.4060.438-0.047
1/20.5000.50000.49750.57150.56501.7191.5315.3445.1568.3448.1560.500-0.050
9/160.5620.56250.56000.64200.63561.8441.6565.8445.6569.0948.9060.562-0.053
5/80.6250.62500.62250.71460.70801.9691.7816.3446.1569.8449.6560.625-0.055
3/40.7500.75000.74700.85800.85122.2192.0317.3447.15611.34411.1560.750-0.070
7/80.8750.87500.87201.00200.99312.4692.2818.3448.15612.84412.6560.875-0.076
11.0001.00000.99701.14701.13502.7192.5319.3449.15614.34414.1561.000-0.081
1 1/41.2501.25001.24301.43371.41383.2502.75011.50011.000--1.2503.7500.092
1 1/21.5001.50001.49301.72041.69813.7503.25013.50013.000--1.5004.5000.104
1 3/41.7501.75001.74302.00721.98254.2503.75015.50015.000--1.7505.2500.115
22.0002.00001.99302.29392.26684.7504.25017.50017.000--2.0006.0000.126
2 1/42.2502.25002.24302.58072.55115.2504.75019.50019.000--2.2506.7500.137
2 3/42.7502.75002.74203.15413.11876.2505.75023.50023.000--2.7508.2500.159
33.0003.00002.99203.44093.40306.7506.25025.50025.000--3.0009.0000.171
  • Row 1 (-): Nominal designation printed "-" (source labels sub-1/16 keys by decimal only); same for rows 1-2.
  • Row 23 (1 1/4): From this size (1 1/4 in) up the source prints "-" in both C long-series columns and a value in L (length of bit) instead — the long-series bit pair is not tabulated for large keys.

Materials

  • Hex keys and bits are commonly through-hardened alloy tool steel; state hardness range and finish (black oxide, bright) at RFQ

Ordering & documentation

Documents

Shipments of Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for hex key sizes chart — inch series per asme b18.3 (0.028 – 3 in across flats), short & long series is 10,000 pieces (applies to the standard sizes and finishes for hex key sizes chart — inch series per asme b18.3 (0.028 – 3 in across flats), short & long series; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for hex key sizes chart — inch series per asme b18.3 (0.028 – 3 in across flats), short & long series run 3–7 days. Quantities or variants of hex key sizes chart — inch series per asme b18.3 (0.028 – 3 in across flats), short & long series outside the standard range are confirmed at quotation.

Storage & shipping

Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store hex key sizes chart — inch series per asme b18.3 (0.028 – 3 in across flats), short & long series dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How do I match a key to a socket screw, and what does the table tell me about rejecting a worn key?

Match by the socket size the screw standard calls out, not by the screw's nominal diameter: ASME B18.3 socket head cap screws assign the socket (across flats) per screw size, and the key's nominal across-flats must equal it — a 1/4-20 socket cap screw takes the 3/16 in key, while the 3/16 in key size is unrelated to the screw's thread. Where the table earns its keep is deciding whether a key is still good: measure across flats with a micrometer and compare against the printed minimum — a 1/4 in key measuring under 0.2485 in has worn past tolerance and will begin to round the screw's socket corners, and the across-corners minimum (0.2815 in for that size) is the faster tell because corner wear shows first. The short/long series choice is an access decision — the long series reaches recessed sockets at some cost in tip engagement rigidity — and from 1 1/4 in upward the source stops tabulating the long-series pair and prints the bit length instead (flagged). The three smallest sizes print no fraction designation, only decimals (0.028/0.035/0.050 in) — reproduced as printed. What the chart cannot tell you: tool steel grade, hardness and coating of the key — per RFQ.

What is the MOQ and lead time for threaded parts and tooling referenced by this chart?

The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Confirm the exact schedule against quantity, size mix and any tooling items at quotation.

What is the MOQ and lead time for Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series state?

State the full designation (ASME B18.3), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your Hex Key Sizes Chart — Inch Series per ASME B18.3 (0.028 – 3 in Across Flats), Short & Long Series
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.